C8051F34A-GM Silicon Laboratories Inc, C8051F34A-GM Datasheet - Page 43

• Manufacturer Part Number: C8051F34A-GM
• Description: IC 8051 MCU 64K FLASH MEM 32-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F34xr

Specifications of C8051F34A-GM

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 32-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4352 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-F34X, KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F340DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 32QFN EP
• Device Core: 8051
• Family Name: C8051F34x
• Maximum Speed: 48 MHz
• Cpu Family: C8051F34x
• Device Core Size: 8b
• Frequency (max): 48MHz
• Total Internal Ram Size: 4.25KB
• # I/os (max): 25
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: QFN EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1748 - ADAPTER TOOLSTICK FOR C8051F34X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1350-5

5.2.
The temperature sensor transfer function is shown in Figure 5.2. The output voltage (V
ADC input when the temperature sensor is selected by bits AMX0P4-0 in register AMX0P. Values for the
Offset and Slope parameters can be found in Table 5.1.
The uncalibrated temperature sensor output is extremely linear and suitable for relative temperature mea-
surements (see Table 5.1 for linearity specifications). For absolute temperature measurements, offset and/
or gain calibration is recommended. Typically a 1-point (offset) calibration includes the following steps:
Figure 5.3 shows the typical temperature sensor error assuming a 1-point calibration at 25 °C. Note that
parameters which affect ADC measurement, in particular the voltage reference value, will also
affect temperature measurement.
Temperature Sensor
Step 1. Control/measure the ambient temperature (this temperature must be known).
Step 2. Power the device, and delay for a few seconds to allow for self-heating.
Step 3. Perform an ADC conversion with the temperature sensor selected as the positive input
Step 4. Calculate the offset characteristics, and store this value in non-volatile memory for use
and GND selected as the negative input.
with subsequent temperature sensor measurements.
Figure 5.2.
C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
V
Temp
TEMP
C
=
= (V
Temperature Sensor Transfer Function
(Gain
TEMP
x Temp
- Offset) /
Temperature
Rev. 1.3
C
) +
Offset
Offset
Gain
(V at 0 Celsius)
Gain
(V / deg C)
TEMP
) is the positive
43