PIC16C770-I/P Microchip Technology, PIC16C770-I/P Datasheet - Page 85

• Manufacturer Part Number: PIC16C770-I/P
• Description: IC MCU CMOS A/D 2K 20MHZ 20-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C770-I/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Type: OTP
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 6x12b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 16
• Ram Memory Size: 256Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• No. Of: RoHS Compliant
• Core: PIC
• Processor Series: PIC16C
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 20 MHz
• Data Ram Size: 256 B
• Data Rom Size: 256 B
• On-chip Adc: 6 bit
• Number Of Programmable I/os: 16
• Number Of Timers: 3 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Mounting Style: Through Hole
• Height: 3.3 mm
• Interface Type: I2C, SPI, SSP
• Length: 26.16 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA16XP200 - ADAPTER ICE 20DIP/SOIC/SSOPAC164028 - MODULE SKT PROMATEII 20SOIC/DIP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC16C770I/P

9.2.4
While in SLEEP mode, the I
receive addresses or data. When an address match or
complete byte transfer occurs, it wakes the processor
from SLEEP (if the SSP interrupt bit is enabled).
9.2.5
A RESET disables the MSSP module and terminates
the current transfer.
FIGURE 9-13:
2002 Microchip Technology Inc.
SDA
SCL
SLEEP OPERATION
EFFECTS OF A RESET
MSSP BLOCK DIAGRAM (I
SDA in
Bus Collision
SCL in
2
C slave module can
Read
Advance Information
MSb
START bit, STOP bit,
Write collision detect
START bit detect,
end of XMIT/RCV
Clock Arbitration
State counter for
STOP bit detect
Acknowledge
Generate
SSPBUF
SSPSR
2
C MASTER MODE)
LSb
Write
9.2.6
Master mode operation supports interrupt generation
on the detection of the START and STOP conditions.
The STOP (P) and START (S) bits are cleared from a
RESET or when the MSSP module is disabled. Control
of the I
bus is idle with both the S and P bits clear.
In Master mode, the SCL and SDA lines are manipu-
lated by the MSSP hardware.
The following events will cause SSP Interrupt Flag bit
(SSPIF) to be set (SSP Interrupt, if enabled):
• START condition
• STOP condition
• Data transfer byte transmitted/received
• Acknowledge transmit
• Repeated START
Clock
Data Bus
Shift
Internal
PIC16C717/770/771
Set/RESET, S, P, WCOL (SSPSTAT)
Set SSPIF, BCLIF
RESET ACKSTAT, PEN (SSPCON2)
2
C bus may be taken when the P bit is set or the
MASTER MODE
SSPADD<6:0>
SSPM<3:0>,
Baud
Rate
Generator
DS41120B-page 83