ATTINY261-15MZ Atmel, ATTINY261-15MZ Datasheet - Page 140

• Manufacturer Part Number: ATTINY261-15MZ
• Description: MCU AVR 2K FLASH 15MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY261-15MZ

• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 16
• Eeprom Size: 128 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Program Memory Size: 2KB (2K x 8)
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

18. AC – Analog Comparator
18.1
18.1.1
140
Register Description
ATtiny261/ATtiny461/ATtiny861
ACSRA – Analog Comparator Control and Status Register A
The Analog Comparator compares the input values on the selectable positive pin (AIN0, AIN1 or
AIN2) and selectable negative pin (AIN0, AIN1 or AIN2). When the voltage on the positive pin is
higher than the voltage on the negative pin, the Analog Comparator output, ACO, is set. The
comparator can trigger a separate interrupt, exclusive to the Analog Comparator. The user can
select Interrupt triggering on comparator output rise, fall or toggle. A block diagram of the com-
parator and its surrounding logic is shown in
Figure 18-1. Analog Comparator Block Diagram
Notes:
• Bit 7 – ACD: Analog Comparator Disable
When this bit is written logic one, the power to the Analog Comparator is switched off. This bit
can be set at any time to turn off the Analog Comparator. This will reduce power consumption in
Active and Idle mode. When changing the ACD bit, the Analog Comparator Interrupt must be
disabled by clearing the ACIE bit in ACSRA. Otherwise an interrupt can occur when the bit is
changed.
• Bit 6 – ACBG: Analog Comparator Bandgap Select
When this bit is set an internal 1.1V reference voltage replaces the positive input to the Analog
Comparator. The selection of the internal voltage reference is done by writing the REFS2..0 bits
in ADMUX register. When this bit is cleared, AIN0, AIN1 or AIN2 depending on the ACM2..0 bits
is applied to the positive input of the analog comparator.
Bit
0x08 (0x28)
Read/Write
Initial Value
AIN0
AIN1
AIN2
1. See
2. Refer to
placement.
ADC MULTIPLEXER
ACM2..1
REFERENCE
ACME
ADEN
Table 18-2 on page
BANDGAP
OUTPUT
ACD
R/W
7
0
Figure 1-1 on page 2
MUX
(1)
ACBG
ACBG
R/W
6
0
142.
ACO
N/A
R
5
and
Table 12.3.2 on page 66
R/W
ACI
4
0
Figure
(2)
18-1.
ACIE
R/W
3
0
ACME
R/W
2
0
for Analog Comparator pin
ACIS1
R/W
1
0
ACIS0
R/W
0
0
7753F–AVR–01/11
ACSRA