PIC16F870T-I/SS Microchip Technology, PIC16F870T-I/SS Datasheet - Page 57

• Manufacturer Part Number: PIC16F870T-I/SS
• Description: IC MCU FLASH 2KX14 EE 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F870T-I/SS

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• For Use With: I3-DB16F871 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.0
Each Capture/Compare/PWM (CCP) module contains
a 16-bit register which can operate as a:
• 16-bit Capture register
• 16-bit Compare register
• PWM Master/Slave Duty Cycle register
Table 8-1 shows the resources and interactions of the
CCP module. In the following sections, the operation of
a CCP module is described.
8.1
Capture/Compare/PWM Register1 (CCPR1) is com-
prised of two 8-bit registers: CCPR1L (low byte) and
CCPR1H (high byte). The CCP1CON register controls
the operation of CCP1. The special event trigger is
generated by a compare match and will reset Timer1
and start an A/D conversion (if the A/D module is
enabled).
REGISTER 8-1:
 2003 Microchip Technology Inc.
CAPTURE/COMPARE/PWM
MODULES
CCP1 Module
bit 7-6
bit 5-4
bit 3-0
CCP1CON REGISTER REGISTER (ADDRESS: 17h/1Dh)
bit 7
Unimplemented: Read as '0'
CCP1X:CCP1Y: PWM Least Significant bits
Capture mode:
Unused
Compare mode:
Unused
PWM mode:
These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L.
CCP1M3:CCP1M0: CCP1 Mode Select bits
0000 = Capture/Compare/PWM disabled (resets CCP1 module)
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4th rising edge
0111 = Capture mode, every 16th rising edge
1000 = Compare mode, set output on match (CCP1IF bit is set)
1001 = Compare mode, clear output on match (CCP1IF bit is set)
1010 = Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP1 pin is
1011 = Compare mode, trigger special event (CCP1IF bit is set, CCP1 pin is unaffected);
11xx = PWM mode
Legend:
R = Readable bit
- n = Value at POR
U-0
—
unaffected)
CCP1resets TMR1, and starts an A/D conversion (if A/D module is enabled)
U-0
—
CCP1X
R/W-0
W = Writable bit
‘1’ = Bit is set
CCP1Y
R/W-0
Additional information on CCP modules is available in
the PICmicro™ Mid-Range MCU Family Reference
Manual (DS33023) and in application note AN594,
“Using the CCP Modules” (DS00594).
TABLE 8-1:
CCP Mode
CCP1M3
Compare
Capture
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
PWM
PIC16F870/871
CCP MODE - TIMER
RESOURCES REQUIRED
CCP1M2 CCP1M1
R/W-0
x = Bit is unknown
Timer Resource
R/W-0
DS30569B-page 55
Timer1
Timer1
Timer2
CCP1M0
R/W-0
bit 0