AT32UC3B0256-A2UR Atmel, AT32UC3B0256-A2UR Datasheet - Page 178

• Manufacturer Part Number: AT32UC3B0256-A2UR
• Description: MCU AVR32 256K FLASH 64-TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B0256-A2UR

• Package / Case: 64-TQFP, 64-VQFP
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 60MHz
• Number Of I /o: 44
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Program Memory Size: 256KB (256K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Core Size: 32-Bit
• Package: 64TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 44
• Interface Type: I2S/SPI/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

17.6.1
32059K–03/2011
Access Types
Table 17-1.
1)
uration section at the end of this chapter.
2)
Each configuration register can be accessed in four different ways. The first address location
can be used to write the register directly. This address can also be used to read the register
value. The following addresses facilitate three different types of write access to the register. Per-
forming a “set” access, all bits written to one will be set. Bits written to zero will be unchanged by
the operation. Performing a “clear” access, all bits written to one will be cleared. Bits written to
zero will be unchanged by the operation. Finally, a toggle access will toggle the value of all bits
written to one. Again all bits written to zero remain unchanged. Note that for some registers (e.g.
IFR), not all access methods are permitted.
Note that for ports with less than 32 bits, the corresponding control registers will have unused
bits. This is also the case for features that are not implemented for a specific pin. Writing to an
unused bit will have no effect. Reading unused bits will always return 0.
Offset
0xBC
0xCC
0xDC
0xB4
0xB8
0xC0
0xC4
0xC8
0xD0
0xD4
0xD8
The reset value for these registers are device specific. Please refer to the Module Config-
The reset value is undefined depending on the pin states.
Glitch Filter Enable Register
Glitch Filter Enable Register
Glitch Filter Enable Register
Glitch Filter Enable Register
Interrupt Mode Register 1
Interrupt Mode Register 1
Interrupt Mode Register 1
Interrupt Flag Register
Interrupt Flag Register
Interrupt Flag Register
Interrupt Flag Register
GPIO Register Memory Map
Register
Read/Write
Function
Toggle
Toggle
Clear
Clear
Read
Clear
Set
Set
-
-
GFERS
GFERC
GFERT
IMR1S
IMR1C
IMR1T
GFER
Name
IFRC
IFR
-
-
Read/Write
Write-Only
Write-Only
Write-Only
Write-Only
Write-Only
Write-Only
Read-Only
Write-Only
Access
-
-
AT32UC3B
Reset value
(1)
(1)
178