ST72C254G2M6 STMicroelectronics, ST72C254G2M6 Datasheet - Page 49

• Manufacturer Part Number: ST72C254G2M6
• Description: IC MCU 8BIT 8K FLASH SOIC-28
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72C254G2M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 3.2 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: ST7
• No. Of I/o's: 22
• Ram Memory Size: 256Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Processor Series: ST72C2x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 3 bit
• Operating Supply Voltage: 3.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7MDT1-DVP2/US
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: In Transition

16-BIT TIMER (Cont’d)
Notes:
1. After a processor write cycle to the OCiHR reg-
2. If the OCiE bit is not set, the OCMPi pin is a
3. When the timer clock is f
4. The output compare functions can be used both
5. The value in the 16-bit OC
Figure 32. Output Compare Block Diagram
16-bit
ister, the output compare function is inhibited
until the OCiLR register is also written.
general I/O port and the OLVLi bit will not
appear when a match is found but an interrupt
could be generated if the OCIE bit is set.
OCMPi are set while the counter value equals
the OCiR register value (see
behavior is the same in OPM or PWM mode.
When the timer clock is f
external clock mode, OCFi and OCMPi are set
while the counter value equals the OCiR regis-
ter value plus 1 (see
for generating external events on the OCMPi
pins even if the input capture mode is also
used.
OLVi bit should be changed after each suc-
cessful comparison in order to control an output
waveform or establish a new elapsed timeout.
16 BIT FREE RUNNING
OC1R Register
OUTPUT COMPARE
16-bit
CIRCUIT
OC2R Register
COUNTER
16-bit
Figure
CPU
9).
i
R register and the
CPU
/4, f
Figure
/2, OCFi and
OC1E
CPU
OCIE
OC2E
OCF1
8). This
/8 or in
ST72104Gx, ST72215Gx, ST72216Gx, ST72254Gx
FOLV2 FOLV1
Forced Compare Output capability
When the FOLVi bit is set by software, the OLVLi
bit is copied to the OCMPi pin. The OLVi bit has to
be toggled in order to toggle the OCMPi pin when
it is enabled (OCiE bit = 1). The OCFi bit is then
not set by hardware, and thus no interrupt request
is generated.
FOLVLi bits have no effect in either One-Pulse
mode or PWM mode.
(Control Register 2) CR2
(Control Register 1) CR1
OCF2
CC1
(Status Register) SR
OLVL2
CC0
0
0
OLVL1
0
Latch
Latch
1
2
OCMP2
OCMP1
Pin
Pin
49/141