MC908GR32AVFAE Freescale Semiconductor, MC908GR32AVFAE Datasheet - Page 54

• Manufacturer Part Number: MC908GR32AVFAE
• Description: IC MCU 8BIT 32K FLASH 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR32AVFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1.5KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Memory
2.7.5 FLASH-2 Page Erase Operation
Use this step-by-step procedure to erase a page (128 bytes) of FLASH-2 memory:
A. Programming and erasing of FLASH locations can not be performed by code being executed from the
B. While these operations must be performed in the order shown, other unrelated operations may occur
C. It is highly recommended that interrupts be disabled during program/erase operations.
In applications that require more than 1000 program/erase cycles, use the 4 ms page erase specification
to get improved long-term reliability. Any application can use this 4 ms page erase specification. However,
in applications where a FLASH location will be erased and reprogrammed less than 1000 times, and
speed is important, use the 1 ms page erase specification to get a shorter cycle time.
54
10. Wait for a time, t
1. Set the ERASE bit and clear the MASS bit in the FLASH-2 control register (FL2CR).
2. Read the FLASH-2 block protect register (FL2BPR).
3. Write any data to any FLASH-2 address within the address range of the page (128 byte block) to
4. Wait for time, t
5. Set the HVEN bit.
6. Wait for time, t
7. Clear the ERASE bit.
8. Wait for time, t
9. Clear the HVEN bit.
same FLASH array.
between the steps. However, care must be taken to ensure that these operations do not access any
address within the FLASH array memory space such as the COP control register (COPCTL) at
$FFFF.
be erased.
MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5
NVS
ERASE
NVH
RCV
(minimum 10 μs).
(minimum 5 μs).
, (typically 1 μs) after which the memory can be accessed in normal read mode.
(minimum 1 ms or 4 ms).
NOTE
Freescale Semiconductor