C8051F343-GQ Silicon Laboratories Inc, C8051F343-GQ Datasheet - Page 108

• Manufacturer Part Number: C8051F343-GQ
• Description: IC 8051 MCU FLASH 32K 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F34xr

Specifications of C8051F343-GQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 21x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2304 B
• Interface Type: I2C, SMBus, SPI, UART, USB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-F34X, KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F340DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 17 Channel
• Package: 32LQFP
• Device Core: 8051
• Family Name: C8051F34x
• Maximum Speed: 48 MHz
• Data Rom Size: 128 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 17
• Height: 1.4 mm
• Length: 7 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 7 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1748 - ADAPTER TOOLSTICK FOR C8051F34X770-1006 - ISP 4PORT FOR SILABS C8051F MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1301

C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
12.1.3. Flash Write Procedure
Bytes in Flash memory can be written one byte at a time, or in groups of two. The FLBWE bit in register
PFE0CN (SFR Definition 10.1) controls whether a single byte or a block of two bytes is written to Flash
during a write operation. When FLBWE is cleared to ‘0’, the Flash will be written one byte at a time. When
FLBWE is set to ‘1’, the Flash will be written in two-byte blocks. Block writes are performed in the same
amount of time as single-byte writes, which can save time when storing large amounts of data to Flash
memory.During a single-byte write to Flash, bytes are written individually, and a Flash write will be per-
formed after each MOVX write instruction. The recommended procedure for writing Flash in single bytes is:
Steps 5-7 must be repeated for each byte to be written.
For block Flash writes, the Flash write procedure is only performed after the last byte of each block is writ-
ten with the MOVX write instruction. A Flash write block is two bytes long, from even addresses to odd
addresses. Writes must be performed sequentially (i.e. addresses ending in 0b and 1b must be written in
order). The Flash write will be performed following the MOVX write that targets the address ending in 1b. If
a byte in the block does not need to be updated in Flash, it should be written to 0xFF. The recommended
procedure for writing Flash in blocks is:
Steps 5–10 must be repeated for each block to be written.
108
Step 1. Disable interrupts.
Step 2. Clear the FLBWE bit (register PFE0CN) to select single-byte write mode.
Step 3. Set the PSWE bit (register PSCTL).
Step 4. Clear the PSEE bit (register PSCTL).
Step 5. Write the first key code to FLKEY: 0xA5.
Step 6. Write the second key code to FLKEY: 0xF1.
Step 7. Using the MOVX instruction, write a single data byte to the desired location within the
Step 8. Clear the PSWE bit.
Step 9. Re-enable interrupts.
Step 1. Disable interrupts.
Step 2. Set the FLBWE bit (register PFE0CN) to select block write mode.
Step 3. Set the PSWE bit (register PSCTL).
Step 4. Clear the PSEE bit (register PSCTL).
Step 5. Write the first key code to FLKEY: 0xA5.
Step 6. Write the second key code to FLKEY: 0xF1.
Step 7. Using the MOVX instruction, write the first data byte to the even block location (ending in
Step 8. Write the first key code to FLKEY: 0xA5.
Step 9. Write the second key code to FLKEY: 0xF1.
Step 10. Using the MOVX instruction, write the second data byte to the odd block location (ending
Step 11. Clear the PSWE bit.
Step 12. Re-enable interrupts.
512-byte sector.
0b).
in 1b).
Rev. 1.3