C8051F019-GQ Silicon Laboratories Inc, C8051F019-GQ Datasheet - Page 118
![IC 8051 MCU 16K FLASH 48TQFP](/photos/12/38/123852/c8051f019-gq_sml.jpg)
C8051F019-GQ
Manufacturer Part Number
C8051F019-GQ
Description
IC 8051 MCU 16K FLASH 48TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F018r
Specifications of C8051F019-GQ
Program Memory Type
FLASH
Program Memory Size
16KB (16K x 8)
Package / Case
48-TQFP, 48-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
16
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.8 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
1.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
16
Number Of Timers
4
Operating Supply Voltage
2.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F005DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
No. Of I/o's
16
Ram Memory Size
1.25KB
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1198
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F019-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F019-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
16.2.
Modes 2 and 3 support multiprocessor communication between a master processor and one or more slave processors
by special use of the ninth data bit. When a master processor wants to transmit to one or more slaves, it first sends
an address byte to select the target(s). An address byte differs from a data byte in that its ninth bit is logic 1; in a
data byte, the ninth bit is always set to logic 0.
Setting the SM2 bit (SCON.5) of a slave processor configures its UART such that when a stop bit is received, the
UART will generate an interrupt only if the ninth bit is logic one (RB8 = 1) signifying an address byte has been
received. In the UART’s interrupt handler, software will compare the received address with the slave’s own
assigned 8-bit address. If the addresses match, the slave will clear its SM2 bit to enable interrupts on the reception
of the following data byte(s). Slaves that weren’t addressed leave their SM2 bits set and do not generate interrupts
on the reception of the following data bytes, thereby ignoring the data. Once the entire message is received, the
addressed slave resets its SM2 bit to ignore all transmissions until it receives the next address byte.
Multiple addresses can be assigned to a single slave and/or a single address can be assigned to multiple slaves,
thereby enabling “broadcast” transmissions to more than one slave simultaneously. The master processor can be
configured to receive all transmissions or a protocol can be implemented such that the master/slave role is
temporarily reversed to enable half-duplex transmission between the original master and slave(s).
RX
Master
Device
Multiprocessor Communications
TX
Figure 16.7. UART Multi-Processor Mode Interconnect Diagram
RX
Device
Slave
TX
Rev. 1.2
RX
Device
Slave
TX
RX
Device
Slave
C8051F018
C8051F019
TX
VDD
118