C8051F019-GQ Silicon Laboratories Inc, C8051F019-GQ Datasheet - Page 76
![IC 8051 MCU 16K FLASH 48TQFP](/photos/12/38/123852/c8051f019-gq_sml.jpg)
C8051F019-GQ
Manufacturer Part Number
C8051F019-GQ
Description
IC 8051 MCU 16K FLASH 48TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F018r
Specifications of C8051F019-GQ
Program Memory Type
FLASH
Program Memory Size
16KB (16K x 8)
Package / Case
48-TQFP, 48-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
16
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.8 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
1.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
16
Number Of Timers
4
Operating Supply Voltage
2.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F005DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
No. Of I/o's
16
Ram Memory Size
1.25KB
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1198
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F019-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F019-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
11.1.
The C8051F018/9 incorporates a power supply monitor that holds the MCU in the reset state until VDD rises above
the V
Characteristics of the power supply monitor circuit.) The /RST pin is asserted (low) until the end of the 100ms
VDD Monitor timeout in order to allow the VDD supply to become stable.
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. All of the other reset
flags in the RSTSRC Register are indeterminate. PORSF is cleared by a reset from any other source. Since all
resets cause program execution to begin at the same location (0x0000), software can read the PORSF flag to
determine if a power-up was the cause of reset. The content of internal data memory should be assumed to be
undefined after a power-on reset.
11.2.
Writing a 1 to the PORSF bit forces a Power-On Reset as described in Section 11.1.
11.3.
When a power-down transition or power irregularity causes VDD to drop below V
will drive the /RST pin low and return the CIP-51 to the reset state (see Figure 11.2). When VDD returns to a level
above V
though internal data memory contents are not altered by the power-fail reset, it is impossible to determine if VDD
dropped below the level required for data retention. If the PORSF flag is set, the data may no longer be valid.
RST
Logic HIGH
Logic LOW
RST
Power-on Reset
Software Forced Reset
Power-fail Reset
level during power-up. (See Figure 11.2 for timing diagram, and refer to Table 11.1 for the Electrical
, the CIP-51 will leave the reset state in the same manner as that for the power-on reset. Note that even
2.80
2.40
2.0
1.0
/RST
V
RST
Figure 11.2. VDD Monitor Timing Diagram
100ms
Rev. 1.2
RST
, the power supply monitor
C8051F018
C8051F019
100ms
t
76