C8051F019-GQ Silicon Laboratories Inc, C8051F019-GQ Datasheet - Page 99
![IC 8051 MCU 16K FLASH 48TQFP](/photos/12/38/123852/c8051f019-gq_sml.jpg)
C8051F019-GQ
Manufacturer Part Number
C8051F019-GQ
Description
IC 8051 MCU 16K FLASH 48TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F018r
Specifications of C8051F019-GQ
Program Memory Type
FLASH
Program Memory Size
16KB (16K x 8)
Package / Case
48-TQFP, 48-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
16
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.8 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
1.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
16
Number Of Timers
4
Operating Supply Voltage
2.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F005DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
No. Of I/o's
16
Ram Memory Size
1.25KB
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1198
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F019-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F019-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
14.2.4. Slave Receiver Mode
Serial data is received on SDA while the serial clock is received on SCL. First, a byte is received that contains an
address and data direction bit. In this case the data direction bit (R/W) will be logic 0 to indicate a “WRITE”
operation. If the received address matches the slave’s assigned address (or a general call address is received) one or
more bytes of serial data are received from the master. After each byte is received, an acknowledge bit is
transmitted by the slave. The master outputs START and STOP conditions to indicate the beginning and end of the
serial transfer.
14.3.
A master may start a transfer only if the bus is free. The bus is free after a STOP condition or after the SCL and
SDA lines remains high for a specified time. Two or more master devices may attempt to generate a START
condition at the same time. Since the devices that generated the START condition may not be aware that other
masters are contending for the bus, an arbitration scheme is employed. The master devices continue to transmit
until one of the masters transmits a HIGH level, while the other(s) master transmits a LOW level on SDA. The first
master(s) transmitting the HIGH level on SDA looses the arbitration and is required to give up the bus.
14.4.
SMBus provides a clock synchronization mechanism, similar to I2C, which allows devices with different speed
capabilities to coexist on the bus. A clock-low extension is used during a transfer in order to allow slower slave
devices to communicate with faster masters. The slave can hold the SCL line LOW to extend the clock low period,
effectively decreasing the serial clock frequency.
14.5.
14.5.1. SCL Low Timeout
If the SCL line is held low by a slave device on the bus, no further communication is possible. Furthermore, the
master cannot force the SCL line high to correct the error condition. To solve this problem, the SMBus protocol
specifies that devices participating in a transfer must detect any clock cycle held low longer than 25ms as a
“timeout” condition. Devices that have detected the timeout condition must reset the communication no later than
10ms after detecting the timeout condition.
One of the MCU’s general-purpose timers, operating in 16-bit auto-reload mode, can be used to monitor the SCL
line for this timeout condition. Timer 3 is specifically designed for this purpose. (Refer to the Timer 3 Section
17.3. for detailed information on Timer 3 operation.)
14.5.2. SCL High (SMBus Free) Timeout
The SMBus specification stipulates that if a device holds the SCL and SDA lines high for more that 50usec, the bus
is designated as free. The SMB0CR register is used to detect this condition when the FTE bit in SMB0CN is set.
14.6.
The SMBus serial interface is accessed and controlled through five SFRs: SMB0CN Control Register, SMB0CR
Clock Rate Register, SMB0ADR Address Register, SMB0DAT Data Register and SMB0STA Status Register. The
system device may have one or more SMBus serial interfaces implemented. The five special function registers
related to the operation of the SMBus interface are described in the following section.
99
C8051F018
C8051F019
Arbitration
Clock Low Extension
Timeouts
SMBus Special Function Registers
Rev. 1.2