AT89LS8252-12JC Atmel, AT89LS8252-12JC Datasheet - Page 14

• Manufacturer Part Number: AT89LS8252-12JC
• Description: IC MICRO CTRL 12MHZ 44PLCC
• Manufacturer: Atmel
• Series: 89LSr

Specifications of AT89LS8252-12JC

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 12MHz
• Connectivity: SPI, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 6 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-PLCC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Data Converters: -
• Other names: AT89LS825212JC

Programmable Clock Out
A 50% duty cycle clock can be programmed to come out on
P1.0, as shown in Figure 5. This pin, besides being a regu-
lar I/0 pin, has two alternate functions. It can be pro-
grammed to input the external clock for Timer/Counter 2 or
to output a 50% duty cycle clock ranging from 61 Hz to 3
MHz at a 12 MHz operating frequency.
To configure the Timer/Counter 2 as a clock generator, bit
C/T2 (T2CON.1) must be cleared and bit T2OE (T2MOD.1)
must be set. Bit TR2 (T2CON.2) starts and stops the timer.
The clock-out frequency depends on the oscillator fre-
quency and the reload value of Timer 2 capture registers
(RCAP2H, RCAP2L), as shown in the following equation.
In the clock-out mode, Timer 2 rollovers will not generate
an interrupt. This behavior is similar to when Timer 2 is
used as a baud-rate generator. It is possible to use Timer 2
as a baud-rate generator and a clock generator simulta-
neously. Note, however, that the baud-rate and clock-out
frequencies cannot be determined independently from one
another since they both use RCAP2H and RCAP2L.
Figure 6. SPI Block Diagram
14
Clock-Out Frequency
AT89LS8252
=
SPI STATUS REGISTER
OSCILLATOR
÷4÷16÷64÷128
------------------------------------------------------------------------------------------ -
4
SELECT
DIVIDER
×
SPI CONTROL
[
65536
Oscillator Frequency
SPI INTERRUPT
–
SPI CLOCK (MASTER)
(
REQUEST
RCAP2H,RCAP2L
MSTR
SPE
8
INTERNAL
MSB
DATA BUS
8/16-BIT SHIFT REGISTER
8
READ DATA BUFFER
)
]
8
SPI CONTROL REGISTER
UART
The UART in the AT89LS8252 operates the same way as
the UART in the AT89C51, AT89C52 and AT89C55. For
further information, see the October 1995 Atmel Microcon-
troller Data Book, page 2-49, section titled, “Serial Inter-
face.”
Serial Peripheral Interface
The serial peripheral interface (SPI) allows high-speed syn-
chronous data transfer between the AT89LS8252 and
peripheral devices or between several AT89LS8252
devices. The AT89LS8252 SPI features include the follow-
ing:
• Full-Duplex, 3-Wire Synchronous Data Transfer
• Master or Slave Operation
• 1.5-MHz Bit Frequency (max.)
• LSB First or MSB First Data Transfer
• Four Programmable Bit Rates
• End of Transmission Interrupt Flag
• Write Collision Flag Protection
• Wakeup from Idle Mode (Slave Mode Only)
CLOCK
LOGIC
LSB
CLOCK
S
M
M
S
S
M
MISO
MOSI
P1.6
P1.5
SCK
P1.4
1.7
SS
0850C–MICRO–3/06