AT89C5131-S3SIL Atmel, AT89C5131-S3SIL Datasheet - Page 35

• Manufacturer Part Number: AT89C5131-S3SIL
• Description: IC 8051 MCU FLASH 32K USB 52PLCC
• Manufacturer: Atmel
• Series: AT89C513xr

Specifications of AT89C5131-S3SIL

• Core Processor: C52X2
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: LED, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 52-PLCC
• For Use With: AT89STK-10 - KIT EVAL APPL MASS STORAGEAT89STK-05 - KIT STARTER FOR AT89C5131
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Data Converters: -

Flash EEPROM Memory
General Description
Features
Flash Programming and
Erasure
4136B–USB–09/03
The Flash memory increases EPROM functionality with in-circuit electrical erasure and
programming. It contains 32 Kbytes of program memory organized in 256 pages of 128
bytes, respectively. This memory is both parallel and serial In-System Programmable
(ISP). ISP allows devices to alter their own program memory in the actual end product
under software control. A default serial loader (bootloader) program allows ISP of the
Flash.
The programming does not require 12V external programming voltage. The necessary
high programming voltage is generated on-chip using the standard V
microcontroller.
•
•
•
•
•
•
•
•
•
•
•
•
•
The 32 Kbytes Flash is programmed by bytes or by pages of 128 bytes. It is not neces-
sary to erase a byte or a page before programming. The programming of a byte or a
page includes a self erase before programming.
There are three methods of programming the Flash memory:
1. The on-chip ISP bootloader may be invoked which will use low level routines to
2. The Flash may be programmed or erased in the end-user application by calling
3. The Flash may be programmed using the parallel method by using a conven-
The bootloader and the Application Programming Interface (API) routines are located in
the Boot ROM.
Flash EEPROM internal program memory.
Boot vector allows user-provided Flash loader code to reside anywhere in the Flash
memory space. This configuration provides flexibility to the user.
Default loader in Boot EEPROM allows programming via the serial port without the
need of a user provided loader.
Up to 64K bytes external program memory if the internal program memory is
disabled (EA = 0).
Programming and erase voltage with standard 5V or 3.3V V
Read/Program/Erase:
Byte-wise read (without wait state).
Byte or page erase and programming (10 ms).
Typical programming time (32 Kbytes) in 10 sec.
Parallel programming with 87C51 compatible hardware interface to programmer.
Programmable security for the code in the Flash.
100K write cycles
10 years data retention
program the pages. The interface used for serial downloading of Flash is the
UART.
low-level routines through a common entry point in the Boot ROM.
tional EPROM programmer. The parallel programming method used by these
devices is similar to that used by EPROM 87C51 but it is not identical and the
commercially available programmers need to have support for the AT89C5131.
CC
AT89C5131
supply.
CC
pins of the
35