ST92F250CV2TB STMicroelectronics, ST92F250CV2TB Datasheet - Page 423

• Manufacturer Part Number: ST92F250CV2TB
• Description: IC MCU 256K FLASH 100-TQFP
• Manufacturer: STMicroelectronics
• Series: ST9r

Specifications of ST92F250CV2TB

• Core Processor: ST9
• Core Size: 8/16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 80
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: ST92F25x
• Core: ST9
• Data Bus Width: 8 bit, 16 bit
• Data Ram Size: 8 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 80
• Number Of Timers: 5 x 16 bit
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST92F150-EPB
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit x 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2140

KNOWN LIMITATIONS (Cont’d)
13.8 EMULATION CHIP LIMITATIONS
Additional limitations exist on Emulation chips (EMU2 emulator). These limitations correspond to those
present in AxxxxxxxxY trace codes (ST92F150). They are listed in the following table.
13.8.1
DIRECTIONAL, WEAK PULL-UP PORTS
This section applies to ports P1[7:3], P4[1], P8[7:2]
and P9[7:0].
During the reset phase (external reset signal low)
and the delay of 20400 clock periods (t
lowing a reset, these ports are in High Impedance
state, while according to the datasheet they should
Table 76. Reset Behaviour Table
Shaded areas represent erroneous operations.
Section 13.8.1
Section 13.8.2
Section 13.8.3
Section 13.8.4
Section 13.8.5
Section 13.8.6
Section 13.8.7
Section 13.8.8
Section 13.8.9
Section 13.8.10
Section 13.8.11
P1[7:3] Bi-Dir + WPU
P8[7:2] Bi-Dir + WPU
P9[7:0] Bi-Dir + WPU
P4.1
Port
Section
RESET
Bi-Dir + WPU
Datasheet
Condition
RESET BEHAVIOUR FOR BI-DIRECTIONAL, WEAK PULL-UP PORTS
HIGH DRIVE I/Os WHEN BSZ=1
ADC PARASITIC DIODE
ADC ACCURACY VS. NEGATIVE INJECTION CURRENT
I2CECCR REGISTER LIMITATION
I2C BEHAVIOUR DISTURBED DURING DMA TRANSACTIONS
MFT DMA MASK BIT RESET
DMA DATA CORRUPTED BY MFT INPUT CAPTURE
SCI-A WRONG BREAK DURATION
LIN MASTER MODE NOT PRESENT ON SCI-A
LIMITATIONS ON LQFP64 PACKAGES
BEHAVIOUR
While RESET
is low
Hi-Z
Hi-Z
Hi-Z
Hi-Z
FOR
RSPH
Port Behaviour
During next
Limitation (AxxxxxxxxY trace code)
20K Clock
) fol-
Cycles
BI-
Hi-Z
Hi-Z
Hi-Z
Hi-Z
ST92F124/F150/F250 - KNOWN LIMITATIONS
have weak pull-ups. These ports then enter Weak
Pull-up state until the user overwrites the reset
values of I/O Port Control Registers PxC0, PxC1
and PxC2.
Rev Z Behaviour
Bi-Dir + WPU
Bi-Dir + WPU
Bi-Dir + WPU
Bi-Dir + WPU
After these
20K Clock
Cycles
PxC0
Control Register Value
0
0
0
0
PxC1
0
0
0
0
PxC2
423/429
0
0
0
0
1