Z8F3201VN020EC00TR Zilog, Z8F3201VN020EC00TR Datasheet - Page 120

• Manufacturer Part Number: Z8F3201VN020EC00TR
• Description: IC ENCORE MCU FLASH 32K 44PLCC
• Manufacturer: Zilog
• Series: Encore!®r

Specifications of Z8F3201VN020EC00TR

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 31
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 44-LCC (J-Lead)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Other names: Z8F3201VN020EC00T

PS017610-0404
SPI Clock Phase and Polarity Control
The Master and Slave are each capable of exchanging a byte of data during a sequence of
eight clock cycles. In both Master and Slave SPI devices, data is shifted on one edge of the
SCK and is sampled on the opposite edge where data is stable. Edge polarity is determined
by the SPI phase and polarity control.
Slave Select
The active Low Slave Select (SS) input signal is used to select a Slave SPI device. SS
must be Low prior to all data communication to and from the Slave device. SS must stay
Low for the full duration of each character transferred. The SS signal may stay Low dur-
ing the transfer of multiple characters or may deassert between each character.
When the SPI on the Z8F640x family device is configured as the only Master in an SPI
system, the SS pin can be set as either an input or an output. For communication between
the Z8F640x family device SPI Master and external Slave devices, the SS signal, as an
output, can assert the SS input pin on one of the Slave devices. Other GPIO output pins
can also be employed to select external SPI Slave devices.
When the SPI on the Z8F640x family device is configured as one Master in a multi-master
SPI system, the SS pin on the should be set as an input. The SS input signal on the Master
must be High. If the SS signal goes Low (indicating another Master is driving the SPI
bus), a Mode Fault error flag is set in the SPI Status register.
The SPI supports four combinations of serial clock phase and polarity using two bits in the
SPI Control register. The clock polarity bit, CLKPOL, selects an active high or active low
clock and has no effect on the transfer format. Table 59 lists the SPI Clock Phase and
Polarity Operation parameters. The clock phase bit, PHASE, selects one of two fundamen-
tally different transfer formats. For proper data transmission, the clock phase and polarity
must be identical for the SPI Master and the SPI Slave. The Master always places data on
the MOSI line a half-cycle before the clock edge (SCK signal), in order for the Slave to
latch the data.
Table 59. SPI Clock Phase (
PHASE
0
0
1
1
CLKPOL
0
1
0
1
PHASE
Transmit
) and Clock Polarity (
Falling
Falling
Rising
Rising
Edge
SCK
Z8F640x/Z8F480x/Z8F320x/Z8F240x/Z8F160x
Receive
Falling
Falling
Rising
Rising
Edge
SCK
CLKPOL
Serial Peripheral Interface
) Operation
SCK
State
High
High
Low
Low
Idle
Z8 Encore!
®
102