C8051F022 Silicon Laboratories Inc, C8051F022 Datasheet - Page 168
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F022
Manufacturer Part Number
C8051F022
Description
IC 8051 MCU 64K FLASH 100TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F02xr
Specifications of C8051F022
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
64
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x10b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F022
Manufacturer:
SILICON
Quantity:
513
Company:
Part Number:
C8051F022
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F022-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F022-GQ
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
C8051F022-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F022R
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
C8051F020/1/2/3
17.1.8. Crossbar Pin Assignment Example
In this example (Figure 17.6), we configure the Crossbar to allocate Port pins for UART0, the SMBus, UART1,
/INT0, and /INT1 (8 pins total). Additionally, we configure the External Memory Interface to operate in Multiplexed
mode and to appear on the Low ports. Further, we configure P1.2, P1.3, and P1.4 for Analog Input mode so that the
voltages at these pins can be measured by ADC1. The configuration steps are as follows:
168
1.
2.
3.
4.
5.
6.
7.
XBR0, XBR1, and XBR2 are set such that UART0EN = 1, SMB0EN = 1, INT0E = 1, INT1E
= 1, and EMIFLE = 1. Thus: XBR0 = 0x05, XBR1 = 0x14, and XBR2 = 0x02.
We configure the External Memory Interface to use Multiplexed mode and to appear on the
Low ports. PRTSEL = 0, EMD2 = 0.
We configure the desired Port 1 pins to Analog Input mode by setting P1MDIN to 0xE3 (P1.4,
P1.3, and P1.2 are Analog Inputs, so their associated P1MDIN bits are set to logic 0).
We enable the Crossbar by setting XBARE = 1: XBR2 = 0x46.
-
-
-
-
-
-
-
We set the UART0 TX pin (TX0, P0.0), UART1 TX pin (TX1, P0.4), ALE, /RD, /WR
(P0.[7:3]) outputs to Push-Pull by setting P0MDOUT = 0xF1.
We configure the output modes of the EMIF Ports (P2, P3) to Push-Pull by setting P2MDOUT
= 0xFF and P3MDOUT = 0xFF.
We explicitly disable the output drivers on the 3 Analog Input pins by setting P1MDOUT =
0x00 (configure outputs to Open-Drain) and P1 = 0xFF (a logic 1 selects the high-impedance
state).
UART0 has the highest priority, so P0.0 is assigned to TX0, and P0.1 is assigned to RX0.
The SMBus is next in priority order, so P0.2 is assigned to SDA, and P0.3 is assigned to SCL.
UART1 is next in priority order, so P0.4 is assigned to TX1. Because the External Memory Inter-
face is selected on the lower Ports, EMIFLE = 1, which causes the Crossbar to skip P0.6 (/RD) and
P0.7 (/WR). Because the External Memory Interface is configured in Multiplexed mode, the Cross-
bar will also skip P0.5 (ALE). RX1 is assigned to the next non-skipped pin, which in this case is
P1.0.
/INT0 is next in priority order, so it is assigned to P1.1.
P1MDIN is set to 0xE3, which configures P1.2, P1.3, and P1.4 as Analog Inputs, causing the
Crossbar to skip these pins.
/INT1 is next in priority order, so it is assigned to the next non-skipped pin, which is P1.5.
The External Memory Interface will drive Ports 2 and 3 (denoted by red dots in Figure 17.6) during
the execution of an off-chip MOVX instruction.
Rev. 1.4