C8051F022 Silicon Laboratories Inc, C8051F022 Datasheet - Page 177
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F022
Manufacturer Part Number
C8051F022
Description
IC 8051 MCU 64K FLASH 100TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F02xr
Specifications of C8051F022
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
64
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 8x10b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F022
Manufacturer:
SILICON
Quantity:
513
Company:
Part Number:
C8051F022
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F022-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F022-GQ
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
C8051F022-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F022R
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
17.2. Ports 4 through 7 (C8051F020/2 only)
All Port pins on Ports 4 through 7 can be accessed as General-Purpose I/O (GPIO) pins by reading and writing the
associated Port Data registers (See Figure 17.21, Figure 17.22, Figure 17.23, and Figure 17.24), a set of SFRs which
are byte-addressable.
A Read of a Port Data register (or Port bit) will always return the logic state present at the pin itself, regardless of
whether the Crossbar has allocated the pin for peripheral use or not. An exception to this occurs during the execution
of a read-modify-write instruction (ANL, ORL, XRL, CPL, INC, DEC, DJNZ, JBC, CLR, SET, and the bitwise MOV
operation). During the read cycle of the read-modify-write instruction, it is the contents of the Port Data register, not
the state of the Port pins themselves, which is read.
17.2.1. Configuring Ports which are not Pinned Out
Although P4, P5, P6, and P7 are not brought out to pins on the C8051F021/3 devices, the Port Data registers are still
present and can be used by software. Because the digital input paths also remain active, it is recommended that these
pins not be left in a ‘floating’ state in order to avoid unnecessary power dissipation arising from the inputs floating to
non-valid logic levels. This condition can be prevented by any of the following:
17.2.2. Configuring the Output Modes of the Port Pins
The output mode of each port pin can be configured to be either Open-Drain or Push-Pull. In the Push-Pull configura-
tion, a logic 0 in the associated bit in the Port Data register will cause the Port pin to be driven to GND, and a logic 1
will cause the Port pin to be driven to VDD. In the Open-Drain configuration, a logic 0 in the associated bit in the
Bit7:
Bit6:
Bits5-4:
Bit3:
Bit2:
Bits1-0:
R/W
IE7
Bit7
1.
2.
3.
IE7: External Interrupt 7 Pending Flag
0: No falling edge has been detected on P3.7 since this bit was last cleared.
1: This flag is set by hardware when a falling edge on P3.7 is detected.
IE6: External Interrupt 6 Pending Flag
0: No falling edge has been detected on P3.6 since this bit was last cleared.
1: This flag is set by hardware when a falling edge on P3.6 is detected.
UNUSED. Read = 00b, Write = don’t care.
IE7CF: External Interrupt 7 Edge Configuration
0: External Interrupt 7 triggered by a falling edge on the IE7 input.
1: External Interrupt 7 triggered by a rising edge on the IE7 input.
IE6CF: External Interrupt 6 Edge Configuration
0: External Interrupt 6 triggered by a falling edge on the IE6 input.
1: External Interrupt 6 triggered by a rising edge on the IE6 input.
UNUSED. Read = 00b, Write = don’t care.
Leave the weak pull-up devices enabled by setting WEAKPUD (XBR2.7) to a logic 0.
Configure the output modes of P4, P5, P6, and P7 to “Push-Pull” by writing P74OUT = 0xFF.
Force the output states of P4, P5, P6, and P7 to logic 0 by writing zeros to the Port Data regis-
ters: P4 = 0x00, P5 = 0x00, P6= 0x00, and P7 = 0x00.
R/W
IE6
Bit6
Figure 17.19. P3IF: Port3 Interrupt Flag Register
Bit5
R
-
Bit4
R
-
IE7CF
R/W
Bit3
Rev. 1.4
IE6CF
R/W
Bit2
C8051F020/1/2/3
R/W
Bit1
-
R/W
Bit0
-
SFR Address:
00000000
Reset Value
0xAD
177