XR20M1172IG28-F Exar Corporation, XR20M1172IG28-F Datasheet - Page 29

• Manufacturer Part Number: XR20M1172IG28-F
• Description: IC UART FIFO I2C/SPI 64B 28TSSOP
• Manufacturer: Exar Corporation

Specifications of XR20M1172IG28-F

• Number Of Channels: 2, DUART
• Package / Case: 28-TSSOP (0.173", 4.40mm Width)
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 1.62 V ~ 3.63 V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Data Rate: 16 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 1.62 V
• Supply Current: 250 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• No. Of Channels: 2
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 1.62V To 3.63V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: TSSOP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1298-5

REV. 1.0.1
IER[5]: Xoff Interrupt Enable (requires EFR bit-4=1)
•
•
IER[6]: RTS# Output Interrupt Enable (requires EFR bit-4=1)
•
•
IER[7]: CTS# Input Interrupt Enable (requires EFR bit-4=1)
•
•
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the
ISR will give the user the current highest pending interrupt level to be serviced, others are queued up to be
serviced next. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt
Source Table,
associated with each of these interrupt levels.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4.4
4.4.1
4.4.2
Logic 0 = Disable the software flow control, receive Xoff interrupt (default).
Logic 1 = Enable the receive Xoff interrupt. See Software Flow Control section for details.
Logic 0 = Disable the RTS# interrupt (default).
Logic 1 = Enable the RTS# interrupt. The UART issues an interrupt when the RTS# pin makes a transition
from low to high.
Logic 0 = Disable the CTS# interrupt (default).
Logic 1 = Enable the CTS# interrupt. The UART issues an interrupt when CTS# pin makes a transition from
low to high.
LSR is by any of the LSR bits 1, 2, 3, 4 and 7.
RXRDY is by RX trigger level.
RXRDY Time-out is by a 4-char plus 12 bits delay timer.
TXRDY is by TX trigger level or TX FIFO empty (or transmitter empty in auto RS-485 control).
MSR is by any of the MSR bits 0, 1, 2 and 3.
GPIO is when any of the GPIO inputs toggle.
Receive Xoff/Special character is by detection of a Xoff or Special character.
CTS# is when its transmitter toggles the input pin (from LOW to HIGH) during auto CTS flow control.
RTS# is when its receiver toggles the output pin (from LOW to HIGH) during auto RTS flow control.
LSR interrupt is cleared by reading all characters with errors out of the RX FIFO.
RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level.
RXRDY Time-out interrupt is cleared by reading RHR.
TXRDY interrupt is cleared by a read to the ISR register or writing to THR.
MSR interrupt is cleared by a read to the MSR register.
GPIO interrupt is cleared by reading the IOState register.
Xoff interrupt is cleared when Xon character(s) is received.
Special character interrupt is cleared by a read to ISR.
RTS# and CTS# flow control interrupts are cleared by a read to the MSR register.
Interrupt Status Register (ISR) - Read-Only
Interrupt Generation:
Interrupt Clearing:
Table
9, shows the data values (bit 0-5) for the interrupt priority levels and the interrupt sources
29
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
XR20M1172