XRP7740ILB-F Exar Corporation, XRP7740ILB-F Datasheet - Page 26

• Manufacturer Part Number: XRP7740ILB-F
• Description: IC CTRLR PWM/LDO STP-DWN 40TQFN
• Manufacturer: Exar Corporation
• Type: Step-Down (Buck)r

Specifications of XRP7740ILB-F

• Number Of Outputs: 5
• Package / Case: 40-WFQFN Exposed Pad
• Topology: Step-Down (Buck) (4), Linear (1)
• Function: Standby Power and GPIOs
• Frequency - Switching: 1.5MHz
• Voltage/current - Output 1: 0.9 V ~ 5.1 V, 5A
• Voltage/current - Output 2: 0.9 V ~ 5.1 V, 15A
• Voltage/current - Output 3: 0.9 V ~ 5.1 V, 5A
• W/led Driver: No
• W/supervisor: Yes
• W/sequencer: No
• Voltage - Supply: 6.5 V ~ 20 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Current - Output: 5A, 15A
• Voltage - Output: 0.9 ~ 5.1 V
• Voltage - Input: 6.5 ~ 20 V
• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Switching Frequency: 300 KHz to 1500 KHz
• Operating Supply Voltage: 6.5 V to 20 V
• Supply Current: 50 mA
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Output Voltage: 0.9 V to 5.1 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 1016-1352 - EVAL BOARD FOR XRP77401016-1344 - IN-SOCKET PROG BRD VIA USB/GUI
• Power - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1353

REV 1.1.0
Phase Shift
Each switching channel can be programmed to a phase shift of the multiples of 90 degrees [for a 4 phase
configuration] or 120 degrees [for a 3 phase configuration]. Two or more of the channels can use the same phase
shift, however, it is preferable to run each channel at separate phases.
GPIO Pins
The General Purpose Input Output (GPIO) Pins are the basic interface between the XRP7740 and the system.
Although all of the stored data within the IC can be read back using the I
have some of those internal register to be displayed and or controlled by a single data pin. Besides simple input
output functions the GPIO pins can be configured to serve as external clock inputs. These pins can be
programmed using OTP bits or can be programmed using the I
user close to 100 different configuration functions that the GPIO can be programmed to do.
NOTE: the GPIO Pins (and all I/Os) should NOT be driven without a 10K resistor when VIN is not being
applied to the IC.
GPIO Pins Polarity
The polarity of the GPIO pin can be set by using the GPIO_ACT_POL register. This register allows any GPIO pin
whether configured as an input or output to change polarity. Bits [5:0] are used to set the polarity of GPIO 0
though 5. If the IC operates in I
Supply Rail Enable
Each GPIO can be configured to enable a specific power rail for the system. The GPIOx_CFG register allows a
GPIO to enable/disable any of the following rails controlled by the chip:
When the configured GPIO is asserted externally, the corresponding rails will be enabled, and they will be
similarly disabled when the GPIO is de-asserted. This supply enabling/disabling can also be controlled through
the I
Power Good Indicator
The GPIO pins can be configured as Power Good indicators for one or more rails. The GPIO pin is asserted
when all rails configured for this specific IO are within specified limits for regulation. This information can also be
found in the READ_PWRGD_SS_FLAG status register.
•
•
•
2
C interface.
A single buck power controller
The Standby LDO
Any mix of the Standby LDO and power controller(s)
EXAR CONFIDENTIAL, PRELIMINARY & PROPRIETARY. DO NOT DISTRIBUTE OR COPY.
EXAR RESERVES THE RIGHT TO MAKE CHANGES TO THIS DATASHEET.
2
C mode, then the commands for Bits [5:4] are ignored.
Quad-Output Digital PWM Buck Controller
26
2
C bus. This GPIO_CONFIG register allows the
2
C bus it is sometimes convenient to
XRP7740