XRP7740ILB-F Exar Corporation, XRP7740ILB-F Datasheet - Page 27

• Manufacturer Part Number: XRP7740ILB-F
• Description: IC CTRLR PWM/LDO STP-DWN 40TQFN
• Manufacturer: Exar Corporation
• Type: Step-Down (Buck)r

Specifications of XRP7740ILB-F

• Number Of Outputs: 5
• Package / Case: 40-WFQFN Exposed Pad
• Topology: Step-Down (Buck) (4), Linear (1)
• Function: Standby Power and GPIOs
• Frequency - Switching: 1.5MHz
• Voltage/current - Output 1: 0.9 V ~ 5.1 V, 5A
• Voltage/current - Output 2: 0.9 V ~ 5.1 V, 15A
• Voltage/current - Output 3: 0.9 V ~ 5.1 V, 5A
• W/led Driver: No
• W/supervisor: Yes
• W/sequencer: No
• Voltage - Supply: 6.5 V ~ 20 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Current - Output: 5A, 15A
• Voltage - Output: 0.9 ~ 5.1 V
• Voltage - Input: 6.5 ~ 20 V
• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Switching Frequency: 300 KHz to 1500 KHz
• Operating Supply Voltage: 6.5 V to 20 V
• Supply Current: 50 mA
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Output Voltage: 0.9 V to 5.1 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 1016-1352 - EVAL BOARD FOR XRP77401016-1344 - IN-SOCKET PROG BRD VIA USB/GUI
• Power - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1353

REV 1.1.0
Fault and Warning Indication
The GPIOs can be configured to signal Fault or Warning conditions when they occur in the chip. Each GPIO can
be configured to signal one of the following:
I
The I
allows for the full control, monitoring, and reconfiguration of the semiconductor.
The I
will work best in their design (in relation to any other I
External Component Selection
Inductor Selection
Select the Inductor for inductance L and saturation current Isat. Select an inductor with Isat higher than the
programmed over current limit. Calculate inductance from:
Keep in mind that a higher Irip results in a smaller inductance value which has the advantages of smaller size,
lower DC equivalent resistance (DCR), and allows the use of a lower output capacitance to meet a given step
load transient. A higher Irip, however, increases the output voltage ripple, requires higher saturation current limit,
and increases critical conduction. Notice that this critical conduction current is half of Irip.
Capacitor Selection
Output Capacitor Selection
Select the output capacitor for voltage rating, capacitance and Equivalent Series Resistance (ESR). Nominally the
voltage rating is selected to be at least twice as large as the output voltage. Select the capacitance to satisfy the
specification for output voltage overshoot/undershoot caused by the current step load. A sudden decrease in the
2
C Communication
•
•
•
•
•
•
2
2
C communication is standard 2-wire communication available between the Host and the IC. This interface
C Slave address is saved in the NVM. Therefore, each customer can choose the 7-bit Slave Address which
OCP Fault on Channel 1 - 4
OCP Warning on Channel 1 - 4
OVP Fault on Channel 1 - 4
UVLO Fault on VIN1 or VIN2
UVLO Warning on VIN1 or VIN2
Over Temperature Fault or Warning
Where:
EXAR CONFIDENTIAL, PRELIMINARY & PROPRIETARY. DO NOT DISTRIBUTE OR COPY.
EXAR RESERVES THE RIGHT TO MAKE CHANGES TO THIS DATASHEET.
VIN is the converter input voltage
VOUT is the converter output voltage
fs is the switching frequency
Irip is the inductor peak-to-peak current ripple (nominally set to 30% of Iout)
Quad-Output Digital PWM Buck Controller
2
C devices on the bus).
27
XRP7740