XRP7740ILB-F Exar Corporation, XRP7740ILB-F Datasheet - Page 28

• Manufacturer Part Number: XRP7740ILB-F
• Description: IC CTRLR PWM/LDO STP-DWN 40TQFN
• Manufacturer: Exar Corporation
• Type: Step-Down (Buck)r

Specifications of XRP7740ILB-F

• Number Of Outputs: 5
• Package / Case: 40-WFQFN Exposed Pad
• Topology: Step-Down (Buck) (4), Linear (1)
• Function: Standby Power and GPIOs
• Frequency - Switching: 1.5MHz
• Voltage/current - Output 1: 0.9 V ~ 5.1 V, 5A
• Voltage/current - Output 2: 0.9 V ~ 5.1 V, 15A
• Voltage/current - Output 3: 0.9 V ~ 5.1 V, 5A
• W/led Driver: No
• W/supervisor: Yes
• W/sequencer: No
• Voltage - Supply: 6.5 V ~ 20 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Current - Output: 5A, 15A
• Voltage - Output: 0.9 ~ 5.1 V
• Voltage - Input: 6.5 ~ 20 V
• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Switching Frequency: 300 KHz to 1500 KHz
• Operating Supply Voltage: 6.5 V to 20 V
• Supply Current: 50 mA
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Output Voltage: 0.9 V to 5.1 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 1016-1352 - EVAL BOARD FOR XRP77401016-1344 - IN-SOCKET PROG BRD VIA USB/GUI
• Power - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1353

REV 1.1.0
load current forces the energy surplus in the inductor to be absorbed by Cout. This causes an overshoot in output
voltage that is corrected by power switch reduced duty cycle. Use the following equation to calculate Cout:
Or it can be expressed approximately as:
Here,
Select ESR such that output voltage ripple (Vrip) specification is met. There are two components in Vrip. First
component arises from the charge transferred to and from Cout during each cycle. The second component of Vrip
is due to the inductor ripple current flowing through the output capacitor’s ESR. It can be calculated for Vrip:
Note that a smaller inductor results in a higher Irip, therefore requiring a larger Cout and/or lower ESR in order to
meet Vrip.
Input Capacitor Selection
Select the input capacitor for Voltage, Capacitance, ripple current, ESR and ESL. Voltage rating is nominally
selected to be at least twice the input voltage. The RMS value of input capacitor current, assuming a low inductor
ripple current, can be approximated as:
Δ
V
=
V
os
Where:
Where:
Where:
−
V
out
EXAR CONFIDENTIAL, PRELIMINARY & PROPRIETARY. DO NOT DISTRIBUTE OR COPY.
is the overshoot voltage deviation.
EXAR RESERVES THE RIGHT TO MAKE CHANGES TO THIS DATASHEET.
L is the output inductance
I2 is the step load high current
I1 is the step load low current
Vos is output voltage including the overshoot
VOUT is the steady state output voltage
Irip is the inductor ripple current
fs is the switching frequency
Cout is the output capacitance
Iin is the RMS input current
Iout is the DC output current
D is the duty cycle
C
out
I
C
in
=
out
=
L
=
I
Quad-Output Digital PWM Buck Controller
out
⋅
V
L
(
os
⋅
I
⋅
2
2
2
(
28
V
−
−
I
D
2
out
V
I
1 ( D
−
1
out
)
Δ ⋅
−
I
2
2
1
)
V
2
)
XRP7740