SX1212IWLTRT Semtech, SX1212IWLTRT Datasheet - Page 47

• Manufacturer Part Number: SX1212IWLTRT
• Description: IC TXRX 300MHZ-510MHZ 32-TQFN
• Manufacturer: Semtech

Specifications of SX1212IWLTRT

• Frequency: 300MHz ~ 510MHz
• Data Rate - Maximum: 150kbps
• Modulation Or Protocol: FSK, OOK
• Applications: AMR, ISM, Home Automation, Process Control
• Power - Output: 12.5dBm
• Sensitivity: -110dBm
• Voltage - Supply: 2.1 V ~ 3.6 V
• Current - Receiving: 3mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFN
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Modulation Type: FSK/OOK
• Package Type: TQFN EP
• Operating Supply Voltage (min): 2.1V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Supplier Unconfirmed
• Other names: SX1212IWLTR

Note that depending upon the application, some uC connections may not be needed:
In addition, DATA pin (unused in buffered mode) should be pulled-up to VDD through a 100 kΩ resistor.
Please refer to Table 13 for the SX1212’s pin configuration.
Table 22: Relevant Configuration Registers in Buffered Mode (data processing related only)
Tx Mode:
Rev 2 – June 18th, 2009
ADVANCED COMMUNICATIONS & SENSING
SYNCParam
IRQParam
MCParam
RXParam
IRQ_0: if none of the relevant IRQ sources are used. In this case, leave floating.
IRQ_1: if none of the relevant IRQ sources are used. In this case, leave floating.
MISO: if no read register access is needed and the chip is used in Tx mode only. In this case, pull up to VDD
through a 100 kΩ resistor.
Configure all data processing related registers listed below appropriately. In this example we assume Sync
word recognition is on and Fifo_fill_method=0.
Program Tx start condition and IRQs: Start Tx when FIFO is not empty (Tx_start_irq_0=1) and IRQ_1 mapped
to Tx_done (Tx_irq_1=1)
Go to Tx mode (and wait for Tx to be ready, see Figure 50)
5.4.5. uC Connections
5.4.6. Buffered Mode Example
Fifo_fill_method
Rx_stby_irq_0
Rx_stby_irq_1
Tx_start_irq_0
Data_mode_x
Sync_value
Fifo_thresh
Sync_size
Fifo_size
Tx_irq_1
Sync_tol
Fifo_fill
Figure 41: uC Connections in Buffered Mode
SX1212
NSS_CONFIG
NSS_DATA
Tx
X
X
X
X
X
IRQ_0
IRQ_1
MOSI
MISO
SCK
Rx
X
X
X
X
X
X
X
X
X
X
Page 47 of 77
Defines data operation mode ( Buffered)
Defines FIFO size
Defines FIFO threshold
Defines IRQ_0 source in Rx & Stby modes
Defines IRQ_1 source in Rx & Stby modes
Defines IRQ_1 source in Tx mode
Defines FIFO filling method
Controls FIFO filling status
Defines Tx start condition and IRQ_0 source
Defines Sync word size
Defines the error tolerance on Sync word detection
Defines Sync word value
uC
Description
www.semtech.com
SX1212