TDA5250 Infineon Technologies, TDA5250 Datasheet - Page 22

• Manufacturer Part Number: TDA5250
• Description: TX/RX ASK/FSK 868-870MHZ 38TSSOP
• Manufacturer: Infineon Technologies
• Type: Transceiverr

Specifications of TDA5250

• Package / Case: 38-TSSOP
• Frequency: 868MHz
• Data Rate - Maximum: 64kbps
• Modulation Or Protocol: ASK, FSK
• Applications: RKE, Remote Control Systems
• Power - Output: 9dBm
• Sensitivity: -109dBm
• Voltage - Supply: 2.1 V ~ 5.5 V
• Current - Receiving: 9mA
• Current - Transmitting: 12mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Operating Frequency: 870 MHz
• Operating Supply Voltage: 2.5 V, 3.3 V, 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 4.4mm
• Product Length (mm): 9.7mm
• Operating Supply Voltage (min): 2.1V
• Operating Supply Voltage (max): 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: SP000012956; TDA5250; TDA5250INTR; TDA5250XT; TDA5250XT

Figure 2-5
2.4.10
The data slicer is a fast comparator with a bandwidth of 100kHz. The self-adjusting threshold is
generated by a RC-network (LPF) or by use of one or both peak detectors depending on the
baseband coding scheme as described in Section 3.6. This can be controlled by the D15 bit of the
CONFIG register as shown in the following table.
Table 2-4
2.4.11
Two separate Peak Detectors are available. They are generating DC voltages in a fast-attack and
slow-release manner that are proportional to the positive and negative peak voltages appearing in
the data signal. These voltages may be used to generate a threshold voltage for non-Manchester
encoded signals, for example. The time-constant of the fast-attack/slow-release action is
determined by the RC network with external capacitor.
2.4.12
The reference oscillator is an NIC oscillator type (Negative Impedance Converter) with a crystal
operating in serial resonance. The nominal operating frequency of 18.083MHz and the frequencies
for FSK modulation can be adjusted via 3 external capacitors. Via microcontroller and bus interface
the chip-internal capacitors can be used for finetuning of the nominal and the FSK modulation
frequencies. This finetuning of the crystal oscillator allows to eliminate frequency errors due to
crystal or component tolerances.
2.4.13
A Bandgap Reference Circuit provides a temperature stable 1.2V reference voltage for the device.
A power down mode is available to switch off all subcircuits that are controlled by the bidirectional
Powerdown&DataDetect PwdDD pin (pin 27) as shown in the following table. Powerdown mode
can either be activated by pin 27 or bit D14 in register 00h. In powerdown mode also pin 28 (DATA)
is affected (see Section 2.4.17).
Data Sheet
D15
Bit
Data Slicer
Peak Detectors
Crystal Oscillator
Bandgap Reference Circuitry & Powerdown
Sub Address 00H: CONFIG
Function
SLICER
Data Filter architecture
ASK / FSK
INTERNAL BUS
0= Lowpass Filter, 1= Peak Detector
22
Description
OTA
Functional Description
Default
TDA5250 D2
Version 1.7
0
2007-02-26
data_filter.wmf