ATMEGA32A-MNR Atmel, ATMEGA32A-MNR Datasheet - Page 120

• Manufacturer Part Number: ATMEGA32A-MNR
• Description: IC MCU AVR 32K 16MHZ 44VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32A-MNR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-VFQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

17.2.1
17.2.2
17.3
17.4
8155C–AVR–02/11
Timer/Counter Clock Sources
Counter Unit
Registers
Definitions
The Timer/Counter (TCNT2) and Output Compare Register (OCR2) are 8-bit registers. Interrupt
request (shorten as Int.Req.) signals are all visible in the Timer Interrupt Flag Register (TIFR).
All interrupts are individually masked with the Timer Interrupt Mask Register (TIMSK). TIFR and
TIMSK are not shown in the figure since these registers are shared by other timer units.
The Timer/Counter can be clocked internally, via the prescaler, or asynchronously clocked from
the TOSC1/2 pins, as detailed later in this section. The asynchronous operation is controlled by
the Asynchronous Status Register (ASSR). The Clock Select logic block controls which clock
source the Timer/Counter uses to increment (or decrement) its value. The Timer/Counter is inac-
tive when no clock source is selected. The output from the Clock Select logic is referred to as the
timer clock (clk
The double buffered Output Compare Register (OCR2) is compared with the Timer/Counter
value at all times. The result of the compare can be used by the waveform generator to generate
a PWM or variable frequency output on the Output Compare Pin (OC2).
Unit” on page 121.
which can be used to generate an output compare interrupt request.
Many register and bit references in this document are written in general form. A lower case “n”
replaces the Timer/Counter number, in this case 2. However, when using the register or bit
defines in a program, the precise form must be used (that is, TCNT2 for accessing
Timer/Counter2 counter value and so on). The definitions in
sively throughout the document.
Table 17-1.
The Timer/Counter can be clocked by an internal synchronous or an external asynchronous
clock source. The clock source clk
bit in the ASSR Register is written to logic one, the clock source is taken from the Timer/Counter
Oscillator connected to TOSC1 and TOSC2. For details on asynchronous operation, see
– Asynchronous Status Register” on page
“Timer/Counter Prescaler” on page
The main part of the 8-bit Timer/Counter is the programmable bi-directional counter unit.
17-2
BOTTOM
MAX
TOP
shows a block diagram of the counter and its surrounding environment.
Definitions
T2
The counter reaches the BOTTOM when it becomes zero (0x00).
The counter reaches its MAXimum when it becomes 0xFF (decimal 255).
The counter reaches the TOP when it becomes equal to the highest value in
the count sequence. The TOP value can be assigned to be the fixed value
0xFF (MAX) or the value stored in the OCR2 Register. The assignment is
dependent on the mode of operation.
).
for details. The compare match event will also set the Compare Flag (OCF2)
T2
132.
is by default equal to the MCU clock, clk
135. For details on clock sources and prescaler, see
Table 17-1
ATmega32A
See “Output Compare
are also used exten-
I/O
. When the AS2
“‘ASSR
Figure
120