WM8351GEB/V Wolfson Microelectronics, WM8351GEB/V Datasheet - Page 218

• Manufacturer Part Number: WM8351GEB/V
• Description: Audio CODECs Audio CODEC plus pwr management
• Manufacturer: Wolfson Microelectronics

Specifications of WM8351GEB/V

• Number Of Adc Inputs: 2
• Number Of Dac Outputs: 2
• Conversion Rate: 48 KSPS
• Interface Type: Serial (2-Wire, 3-Wire, 4-Wire)
• Resolution: 12 bit
• Operating Supply Voltage: 3.7 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: BGA
• Minimum Operating Temperature: - 25 C
• Number Of Channels: 2 ADC/2 DAC
• Supply Current: 260 uA
• Thd Plus Noise: - 83 dB
• Audio Codec Type: Stereo
• No. Of Adcs: 2
• No. Of Dacs: 2
• No. Of Input Channels: 8
• No. Of Output Channels: 6
• Adc / Dac Resolution: 24bit
• Adcs / Dacs Signal To Noise Ratio: 95dB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

REGISTER
WM8351
27 REGISTER BITS BY ADDRESS
ADDRESS
Register 00h Reset/ID
Register 01h ID
Register 02h Revision
REGISTER
w
REGISTER
REGISTER
ADDRESS
ADDRESS
ADDRESS
R1 (01h) ID
R0 (00h)
Reset/ID
Control 1
R2 (02h)
R3 (03h)
Revision
System
BIT
15:0
15:12
11:10
BIT
BIT
BIT
7:0
7:0
15
14
13
12
SW_RESET/CHIP_ID[15:0] 0110_0001_0100_0011 Reading this register returns 6143h.
MASK_REV[7:0] 0000_0001 The ROM Mask ID
CONF_STS[1:0]
CHIP_REV[3:0]
VCC_FAULT_OV
CUST_ID[7:0]
POWERCYCLE
LABEL
LABEL
SYS_RST
CHIP_ON
LABEL
LABEL
DEFAULT
DEFAULT
0000_0000 The Chip Revision Number
DEFAULT
0000
00
0
0
0
1
The functional silicon revision - this tracks changes in
functionality which are separate from ROM mask
settings
The state of the configuration pins. This selects what
register defaults should be.
DEFAULT
Indicates whether the system is on or off. Writing
0 to this bit powers down the whole chip. Registers
which are affected by state machine reset will get
reset.
Once the system is turned OFF it can be restarted
by any of the valid ON event.
Reset by state machine. Default held in metal
mask.
Allows the processors to reboot itself
0 = Do nothing
1 = Perform a processor reset by asserting the
/RST and /MEMRST (GPIO) pins for the
programmed duration
Protected by security key. Reset by state machine.
Default held in metal mask.
Action to take on a fault (if response is set to
shutdown system):
0 = Shut down
1 = Shutdown everything then go through startup
sequence. i.e. Reboot the system.
Include over voltage in the /VCC_FAULT pin
(Alternative GPIO function)
0 = Do not include over voltage in the
/VCC_FAULT signal
1 = Include the over voltage in the /VCC_FAULT
signal
Reset by state machine. Default held in metal
mask.
DESCRIPTION
DESCRIPTION
DESCRIPTION
Never reset.
DESCRIPTION
PD, March 2010, Rev 4.2
REFER TO
REFER TO
REFER TO
REFER TO
Production Data
218