PIC12F1822-I/SN Microchip Technology, PIC12F1822-I/SN Datasheet - Page 277

• Manufacturer Part Number: PIC12F1822-I/SN
• Description: 3.5 KB Flash, 128 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core 8 S
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 12Fr

Specifications of PIC12F1822-I/SN

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• No. Of I/o's: 6
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 128Byte
• Embedded Interface Type: AUSART, EUSART, I2C, SPI
• No. Of Pins: 8
• Peak Reflow Compatible (260 C): Yes
• Rohs Compliant: Yes
• Processor Series: PIC12F
• Core: PIC
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

25.6.13.3
Bus collision occurs during a Stop condition if:
a)
b)
FIGURE 25-38:
FIGURE 25-39:
 2010 Microchip Technology Inc.
After the SDA pin has been deasserted and
allowed to float high, SDA is sampled low after
the BRG has timed out.
After the SCL pin is deasserted, SCL is sampled
low before SDA goes high.
SDA
SCL
PEN
BCL1IF
P
SSP1IF
SDA
SCL
PEN
BCL1IF
P
SSP1IF
Bus Collision During a Stop
Condition
BUS COLLISION DURING A STOP CONDITION (CASE 1)
BUS COLLISION DURING A STOP CONDITION (CASE 2)
SDA asserted low
Assert SDA
PIC12F/LF1822/PIC16F/LF1823
T
BRG
T
BRG
Preliminary
T
BRG
T
BRG
The Stop condition begins with SDA asserted low.
When SDA is sampled low, the SCL pin is allowed to
float. When the pin is sampled high (clock arbitration),
the Baud Rate Generator is loaded with SSP1ADD and
counts down to 0. After the BRG times out, SDA is
sampled. If SDA is sampled low, a bus collision has
occurred. This is due to another master attempting to
drive a data ‘0’
low before SDA is allowed to float high, a bus collision
occurs. This is another case of another master
attempting to drive a data ‘0’
SCL goes low before SDA goes high,
set BCL1IF
T
(Figure
BRG
T
BRG
25-37). If the SCL pin is sampled
(Figure
SDA sampled
low after T
set BCL1IF
’0’
’0’
DS41413B-page 277
’0’
’0’
25-38).
BRG
,