11730D AGILENT TECHNOLOGIES, 11730D Datasheet - Page 104

• Manufacturer Part Number: 11730D
• Description: SENSOR CABLE, 50FT
• Manufacturer: AGILENT TECHNOLOGIES

Specifications of 11730D

• Leaded Process Compatible: No
• Peak Reflow Compatible (260 C): No
• Cable Length: 50ft
• Features: Reduces RFI Effect On Low Power Readings With Improved Shielding Design
• Cable Assembly Type: Sensor
• Cable Color: Gray
• Rohs Compliant: No
• For Use With: 8480 & E-Series Power Sensors
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Agilent 8766/67/68/69 series
Multiport – high performance
Agilent 87104A, B, C and 87106A, B, C multiport switches
operate up to 26.5 GHz. These switches offer warranted
repeatability of 0.03 dB maximum over 5 million switching cycles.
For rigorous requirements such as matrix switching, you can rely
on port-to-port isolation of better than 100 dB at 4 GHz, 70 dB at
20 GHz, and 65 dB at 26.5 GHz. When used in switching trees or
in full access matrixes, isolation and insertion loss repeatability is
crucial to measurement confidence.
Agilent 87104 is a single-pole-4-throw (SP4T) and the Agilent
87106 is a SP6T function. Both switches have internal solid-state
logic that automatically programs the non-used ports to a matched
load when any one port is programmed to “on”. This relieves the
user from having to provide external logic drive pulses. For user-
designed circuit drivers, Option T24 is available. It provides internal
circuits that are compatible with external TTL/5V CMOS digital ICs.
Internal current interrupts and position indicators are
optoelectronically coupled to the electromechanical switch action.
These solenoids are all magnetically latched, eliminating the need
for maintaining coil current. This provides highly-reliable solenoid
control along with accurate position indication to monitor circuits.
Unselected RF ports are terminated in a well-matched 50 ohm
load for eliminating unwanted reflections in unused signal lines.
The Agilent 87104/106 models have the capability to perform
switching with a make-before-break action, by energizing the coils
in the proper logic sequence. When this function is engaged, the
impedance momentarily goes to 25 ohms, and then returns to the
nominal 50 ohm match.
The standard Agilent 87204/206 provides a 16-pin drive
connector while Option 100 provides solder terminals. The Agilent
87204/206 can perform make-before-break or break-before-make
switching.
Agilent 87104/106 series
Transfer
The Agilent 87222C/D/E transfer switches can be used in many
different applications to increase system flexibility and simplify
system design. The following are five examples: switch between
two inputs and two outputs, use as a drop-out switch, use for
signal reversal, configure as a SPDT switch, and bypass an
active device.
Matrix
The 87406B matrix switch consists of 6 ports which can be
individually connected via internal microwave switches to form
an RF path. The switch can be configured for blocking 1 x 5,
2 x 4, or 3 x 3 switching applications.
GPIB compatibility
All of the Agilent switch families can be remotely and
automatically controlled from switch driver instruments such as the
Agilent 11713A or 3488A. These drivers are all GPIB (IEEE 488)
compatible. Drivers are also available for Agilent VXI and Agilent
VEE systems.
Switch driver cables
For complete cable configuration information, request publication
number 5989-3703EN, Agilent 11713A Switch and Attenuator
Driver Configuration Guide.
www.agilent.com/find/mta
Agilent 87204/206 series
Switches (continued)
Switches
93
15