DS33X42DK Maxim Integrated Products, DS33X42DK Datasheet - Page 58
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS33X42DK
Manufacturer Part Number
DS33X42DK
Description
Power Management Modules & Development Tools Ethernet Over PDH Ma PDH Mapping Devices
Manufacturer
Maxim Integrated Products
Datasheet
1.DS33X11.pdf
(375 pages)
Specifications of DS33X42DK
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 58 of 375
- Download datasheet (3Mb)
8.14 Flow Control
In some applications, Flow Control may be required to ensure that data queues do not overflow and frames are not
dropped. The device allows for optional IEEE 802.3 Compliant flow control. There are 2 basic mechanisms of flow
control:
Several conditions can initiate the flow control mechanism:
The Pause time value that is transmitted in outgoing Pause frames is user-programmable in the SU.MACFCR
register. Note that Pause control frame transmission must also be enabled with the SU.MACFCR.TFE bit. Pause
frame receipt must be enabled with SU.MACFCR.RFE. Although not commonly used, Unicast Pause frame
reception can be enabled with SU.MACFCR.UP.
The Watermark value programmed into AR.LQW is in units of memory from the top of the queue, thus a larger
value in AR.LQW indicates that more memory will remain available in the queue when flow control is exerted. Note
that in order to use flow control, the minimum LAN queue size is 2 frames (of maximum size) deep and the LAN
queue watermark threshold (AR.LQW) must be set to allow a minimum of 1 frame of maximum size to be received
after the threshold is crossed. If the Watermark is set too close to the top of the queue to allow time for the remote
node to respond, automatic flow control will not be effective.
In some applications, Ethernet flow control can interfere with higher-layer flow control protocols. For example,
TCP/IP flow control depends on lost frames in order to detect when it has exceeded a system’s capabilities. TCP/IP
flow control uses an increasing flow rate until lost frames are detected, at which point a back-off & resend algorithm
is used, based on the number of lost frames until a steady stream is maintained. If no frames are lost, TCP/IP will
continue attempting to increase the flow rate. If TCP/IP flow control is used in conjunction with Ethernet Flow
control, the results may be undesirable for some applications. The system architect should carefully study this
topic to determine if the system in design should use Ethernet flow control or frame discarding. The
DS33X162 family of devices support both flow control and frame discarding.
Rev: 063008
________________________________________________ DS33X162/X161/X82/X81/X42/X41/X11/W41/W11
•
•
•
•
•
In half duplex mode, a jam sequence is sent that causes a collision detection at the far end. The collision
causes the transmitting node to reduce the rate of transmission.
In full duplex mode, flow control is initiated by the receiving node sending a pause frame. The pause frame
contains a time parameter that determines the pause timeout to be used by the transmitting node.
Flow Control can be initiated by a LAN Queue filling above the Watermark programmed in AR.LQW. Flow
Control for each LAN Queue is independanty enabled in the SU.LQXPC register. Note that the LAN
Queues are external DDR SDRAM buffers used to store data that has arrived on the MII/RMII/GMII
interface(s) and has been processed by the receive MAC.
Flow Control can be initiated by the CIR Policing function. More information on this function can be found
in Section 8.21.
Transmission of a pause frame can be manually initiated by writing a 1 to SU.MACFCR.FCB.
58 of 375
Related parts for DS33X42DK
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![MAX7528KCWP](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
![MAX2606EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2608EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2831EVKIT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
![MAX4888CETI+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: