ISP1109BS,118 NXP Semiconductors, ISP1109BS,118 Datasheet - Page 17

• Manufacturer Part Number: ISP1109BS,118
• Description: RF Transceiver USB FS TRANSCVR
• Manufacturer: NXP Semiconductors

Specifications of ISP1109BS,118

• Number Of Transceivers: 1
• Esd Protection: YeskV
• Power Supply Requirement: Triple
• Operating Supply Voltage (typ): Not RequiredV
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): Not RequiredV
• Operating Supply Voltage (min): Not RequiredV
• Pin Count: 32
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Operating Supply Voltage: 1.65 V to 5.25 V
• Lead Free Status / RoHS Status: Compliant
• Other names: 935276024118 ISP1109BS-T

Philips Semiconductors
Table 10:
Table 11:
9397 750 13355
Product data sheet
V
off
off
on
on
on
on
Pin name
V
V
ISET
DP
DM
RCV
VP, VM, SPI_MISO, UART_RXD
RESET_N, SPEED, SUSPEND,
SPI_I2C_SEL, SPI_MOSI/I2C_SDA,
SPI_CLK/I2C_CLK, SPI_CS/I2C_ADR,
SE0/VM, DAT/VP, UART_TXD, INT_N
MIC, SPKR_R, SPKR_L, ID, V
ID_PU
CC
CC
CC(I/O)
, REG3V3
, V
REF
ISP1109 power modes: summary
ISP1109 pin states in disable or isolate mode
V
off
on
off
off
on
on
CC(I/O)
8.2.1 I
8.2.2 SPI mode
8.2 Serial control modes
Table 11
In I
serial controller through the SCL and SDA lines. The serial controller has a built-in I
slave function. An external I
ISP1109 through the I
The supported I
010 110Xb, where X is determined by pin 13.
In this mode, an external SoC directly communicates with the serial controller through the
SPI interface: SPI_MOSI, SPI_MISO, SPI_CLK, SPI_CS. The serial controller has a
built-in SPI slave function. An external SPI master can access the internal registers of the
ISP1109 through the SPI interface. The maximum SPI clock rate is 26 MHz.
V
X
X
<V
>V
X
X
2
C-bus mode
BUS
th(svc)
th(svc)
2
C-bus mode, an external System-on-a-Chip (SoC) directly communicates with the
BUS
shows the pin states in disable or isolate mode.
Disable mode
(V
powered
not present
drive HIGH or LOW
high-Z
15 k pull-down enabled
high-Z
high-Z
high-Z
high-Z
V
pin ID > V
PWR_DN (bit)
X
X
X
X
0
1
2
REF
C-bus bit rate is up to 400 kbit/s. The I
CC
= on, V
(high-Z, if voltage on
2
C-bus interface.
Rev. 01 — 14 July 2005
REF
CC(I/O)
)
2
C-bus master can access the internal registers of the
I
yes
yes
yes
no
no
yes
CC
= off)
< 20 A
ISET (pin)
high-Z
high-Z
LOW
LOW or HIGH
LOW or HIGH
LOW or HIGH
USB transceiver with carkit support
Isolate mode
(V
not present
powered
high-Z
high-Z
high-Z
drive LOW
drive HIGH
high-Z
high-Z
V
pin ID > V
REF
CC
2
C-bus device address is
= off, V
(high-Z, if voltage on
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Comment
power off
isolate mode
disable mode (Power-down)
disable mode (ISET operation)
normal mode (full operation)
normal mode (Power-down)
REF
CC(I/O)
)
= on)
ISP1109
2
16 of 59
C-bus