ISP1109BS,118 NXP Semiconductors, ISP1109BS,118 Datasheet - Page 22

• Manufacturer Part Number: ISP1109BS,118
• Description: RF Transceiver USB FS TRANSCVR
• Manufacturer: NXP Semiconductors

Specifications of ISP1109BS,118

• Number Of Transceivers: 1
• Esd Protection: YeskV
• Power Supply Requirement: Triple
• Operating Supply Voltage (typ): Not RequiredV
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): Not RequiredV
• Operating Supply Voltage (min): Not RequiredV
• Pin Count: 32
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Operating Supply Voltage: 1.65 V to 5.25 V
• Lead Free Status / RoHS Status: Compliant
• Other names: 935276024118 ISP1109BS-T

Philips Semiconductors
Table 19:
9397 750 13355
Product data sheet
Bit
Symbol
Reset
Access
Mode Control 1 register (address Set = 04h, Clear = 05h) bit allocation
9.1.1.3 Version ID register
9.1.2.1 Mode Control 1 register
9.1.2.2 Mode Control 2 register
UART_PIN
9.1.2 Control registers
R/S/C
_SEL
7
0
Table 17:
Legend: * reset value
Table 18
Table 18:
Legend: * reset value
The bit allocation of the Mode Control 1 register is given in
Table 20:
For the bit allocation of this register, see
Bit
15 to 0
Bit
15 to 0
Bit
7
6
5 to 4
3
2
1
0
UART_EN
R/S/C
6
0
shows the bit description of the register.
Symbol
UART_PIN_
SEL
UART_EN
-
TRANSP_EN
DAT_SE0
SUSPEND
SPEED
Symbol
PRODUCTID[15:0]
PRODUCTID - Product ID register (address 02h to 03h) bit description
VERSIONID - Version ID register (address 14h to 15h) bit description
Mode Control 1 register (address Set = 04h, Clear = 05h) bit description
Symbol
VERSIONID[15:0]
R/S/C
5
0
reserved
Rev. 01 — 14 July 2005
Description
Select UART interface pins for transparent UART mode.
0 — UART_TXD
1 — DAT/VP
When asserted, the ATX is in transparent UART mode.
0 — UART mode is not enabled
1 — UART mode is enabled.
reserved; cleared (set to 0)
When set, the ATX is in transparent mode.
0 — VP_VM mode
1 — DAT_SE0 mode.
Sets the transceiver in low power mode.
0 — Active power mode
1 — Low power mode (differential receiver is disabled if SPEED = 1).
Set the rise time and the fall time of the transmit driver in USB modes.
0 — Low-speed mode
1 — Full-speed mode.
R/S/C
Access
R
Access
R
4
0
DP; SE0/VM
Table
TRANSP_
R/S/C
DM; UART_RXD
Value
1109h*
Value
0110h*
EN
3
0
21.
USB transceiver with carkit support
Description
Product ID of the ISP1109
DAT_SE0
DM.
Description
Version number of the ISP1109
R/S/C
2
1
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Table
DP
19.
SUSPEND
R/S/C
1
0
ISP1109
SPEED
R/S/C
0
0
21 of 59