ISP1109BS,118 NXP Semiconductors, ISP1109BS,118 Datasheet - Page 38

• Manufacturer Part Number: ISP1109BS,118
• Description: RF Transceiver USB FS TRANSCVR
• Manufacturer: NXP Semiconductors

Specifications of ISP1109BS,118

• Number Of Transceivers: 1
• Esd Protection: YeskV
• Power Supply Requirement: Triple
• Operating Supply Voltage (typ): Not RequiredV
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): Not RequiredV
• Operating Supply Voltage (min): Not RequiredV
• Pin Count: 32
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Operating Supply Voltage: 1.65 V to 5.25 V
• Lead Free Status / RoHS Status: Compliant
• Other names: 935276024118 ISP1109BS-T

Philips Semiconductors
14. Static characteristics
Table 48:
V
[1]
[2]
[3]
Table 49:
V
[1]
[2]
9397 750 13355
Product data sheet
Symbol
Voltage
Current
I
I
I
I
I
I
I
Symbol
Input level voltage
V
V
Output level voltage
V
V
Leakage current
I
Open-drain output current
I
Capacitance
C
V
CC
CC(I/O)
CC(I/O)(isolate)
CC(idle)
CC(I/O)(static)
CC(pd)
VREF
LI
OZ
CC
CC
IL
IH
OL
OH
IN
O(REG3V3)
= 3.0 V to 5.25 V; V
In Power-down mode, the minimum voltage is 2.7 V.
Maximum value characterized only, not tested in production. Typical value measured at V
Excluding any load current to the 1.5 k and 15 k pull-up and pull-down resistors (200 A typical).
= 3.0 V to 5.25 V; V
Not applicable for open-drain outputs.
V
CC(I/O)
is not greater than V
Static characteristics: supply pins
Static characteristics: digital pins (except for ISET)
Parameter
regulated supply voltage
output
operating supply current
operating I/O supply current
isolate mode I/O supply current V
supply current during
full-speed idle and SE0
static I/O supply current
Power-down mode supply
current
supply current on pin V
Parameter
LOW-level input voltage
HIGH-level input voltage
LOW-level output voltage
HIGH-level output voltage
input leakage current
OFF-state output current
input capacitance
CC(I/O)
CC(I/O)
O(REG3V3)
= 1.65 V to 3.6 V; T
= 1.65 V to 3.6 V; T
.
REF
Conditions
I
transmitting and receiving at
12 Mbit/s; C
pins DP and DM
transmitting and receiving at
12 Mbit/s
idle: V
SE0: V
idle, SE0 or suspend
bit PWR_DN = 1 or
V
LOAD
Conditions
I
I
I
I
pin to GND
CC
CC(I/O)
amb
amb
OL
OL
OH
OH
Rev. 01 — 14 July 2005
not connected
= 2 mA
= 100 A
= 2 mA
= 100 A
= 40 C to +85 C; unless otherwise specified.
= 40 C to +85 C; unless otherwise specified.
DP
DP
300 A
= 0 V
> 2.7 V, V
< 0.3 V, V
L
= 50 pF on
DM
[1]
[2]
DM
< 0.3 V;
Min
-
0.6V
-
-
V
V
-
< 0.3 V
1
5
CC(I/O)
CC(I/O)
CC(I/O)
0.4 V
0.15 V
USB transceiver with carkit support
CC
[1]
[2]
[2]
[3]
[3]
= 5 V, V
Min
3.0
-
-
-
-
-
-
-
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Typ
-
-
-
-
-
-
-
-
-
CC(I/O)
Typ
3.3
4
1
-
-
-
-
-
= 1.8 V and T
Max
0.3V
-
0.4
0.15
-
-
+1
+5
10
ISP1109
CC(I/O)
Max
3.6
8
2
10
300
20
20
100
amb
= 25 C.
37 of 59
Unit
V
mA
mA
Unit
V
V
V
V
V
V
pF
A
A
A
A
A
A
A