PIC24FV16KA301-I/P Microchip Technology, PIC24FV16KA301-I/P Datasheet - Page 218

• Manufacturer Part Number: PIC24FV16KA301-I/P
• Description: MCU 16KB FLASH 2KB RAM 20-PDIP
• Manufacturer: Microchip Technology

Specifications of PIC24FV16KA301-I/P

• Controller Family/series: PIC24F
• Core Size: 16bit
• No. Of I/o's: 17
• Program Memory Size: 16KB
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 2KB
• Cpu Speed: 32MHz
• Oscillator Type: External, Internal
• Rohs Compliant: Yes
• Processor Series: PIC24FV
• Core: PIC
• Data Bus Width: 16 bit
• Program Memory Type: Flash
• Data Ram Size: 2 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Package / Case: PDIP-20
• Development Tools By Supplier: MPLAB IDE Software
• Minimum Operating Temperature: - 40 C
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24FV32KA304 FAMILY
REGISTER 22-4:
DS39995B-page 218
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9-8
bit 7-4
bit 3-2
bit 1-0
R/W-0
ASEN
U-0
—
ASEN: Auto-Scan Enable bit
1 = Auto-scan is enabled
0 = Auto-scan is disabled
LPEN: Low-Power Enable bit
1 = Return to Low-Power mode after scan
0 = Remain in Full-Power mode after scan
CTMREQ: CTMU Request bit
1 = CTMU is enabled when the ADC is enabled and active
0 = CTMU is not enabled by the ADC
BGREQ: Band Gap Request bit
1 = Band gap is enabled when the ADC is enabled and active
0 = Band gap is not enabled by the ADC
VRSREQ: VREG Scan Request bit
1 = On-chip regulator is enabled when the ADC is enabled and active
0 = On-chip regulator is not enabled by the ADC
Unimplemented: Read as ‘0’
ASINT<1:0>: Auto-Scan (Threshold Detect) Interrupt Mode bits
11 = Interrupt after Threshold Detect sequence completed and valid compare has occurred
10 = Interrupt after valid compare has occurred
01 = Interrupt after Threshold Detect sequence completed
00 = No interrupt
Unimplemented: Read as ‘0’
WM<1:0>: Write Mode bits
11 = Reserved
10 = Auto-compare only (conversion results are not saved, but interrupts are generated when a valid
01 = Convert and save (conversion results are saved to locations as determined by register bits when
00 = Legacy operation (conversion data saved to location determined by buffer register bits)
CM<1:0>: Compare Mode bits
11 = Outside Window mode (valid match occurs if the conversion result is outside of the window defined by
10 = Inside Window mode (valid match occurs if the conversion result is inside the window defined by the
01 = Greater Than mode (valid match occurs if the result is greater than value in the corresponding buffer
00 = Less Than mode (valid match occurs if the result is less than value in the corresponding buffer register)
R/W-0
LPEN
U-0
—
match, as defined by CM and ASINT bits, occurs)
a match, as defined by CM bits, occurs)
the corresponding buffer pair)
corresponding buffer pair)
register)
AD1CON5: A/D CONTROL REGISTER 5
W = Writable bit
‘1’ = Bit is set
CTMREQ
R/W-0
U-0
—
BGREQ
R/W-0
U-0
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
VRSREQ
R/W-0
R/W-0
WM1
R/W-0
WM0
U-0
—
 2011 Microchip Technology Inc.
x = Bit is unknown
ASINT1
R/W-0
R/W-0
CM1
ASINT0
R/W-0
R/W-0
CM0
bit 8
bit 0