EP4CGX150CF23I7N Altera, EP4CGX150CF23I7N Datasheet - Page 71

• Manufacturer Part Number: EP4CGX150CF23I7N
• Description: IC CYCLONE IV FPGA 150K 484FBGA
• Manufacturer: Altera
• Series: CYCLONE® IV GXr

Specifications of EP4CGX150CF23I7N

• Number Of Logic Elements/cells: 149760
• Number Of Labs/clbs: 9360
• Total Ram Bits: 6480000
• Number Of I /o: 270
• Voltage - Supply: 1.16 V ~ 1.24 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 484-FBGA
• Family Name: Cyclone IV
• Number Of Logic Blocks/elements: 149760
• # I/os (max): 270
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 149760
• Ram Bits: 6635520
• Operating Supply Voltage (min): 1.16V
• Operating Supply Voltage (max): 1.24V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant

Chapter 5: Clock Networks and PLLs in Cyclone IV Devices
Clock Networks
Clock Control Block
© December 2010 Altera Corporation
f
1
If you do not use dedicated clock pins to feed the GCLKs, you can use them as
general-purpose input pins to feed the logic array. However, when using them as
general-purpose input pins, they do not have support for an I/O register and must
use LE-based registers in place of an I/O register.
For more information about how to connect the clock and PLL pins, refer to the
Cyclone IV Device Family Pin Connection
The clock control block drives the GCLKs. Clock control blocks are located on each
side of the device, close to the dedicated clock input pins. GCLKs are optimized for
minimum clock skew and delay.
Table 5–4
GCLKs.
Table 5–4. Clock Control Block Inputs
In Cyclone IV devices, dedicated clock input pins, PLL counter outputs, dual-purpose
clock I/O inputs, and internal logic can all feed the clock control block for each GCLK.
The output from the clock control block in turn feeds the corresponding GCLK. The
GCLK can drive the PLL input if the clock control block inputs are outputs of another
PLL or dedicated clock input pins. There are five or six clock control blocks on each
side of the device periphery—depending on device density; providing up to 30 clock
control blocks in each Cyclone IV GX device. The maximum number of clock control
blocks per Cyclone IV E device is 20. For the clock control block locations, refer to
Figure 5–2 on page
The clock control blocks on the left side of the Cyclone IV GX device do not support
any clock inputs.
The control block has two functions:
■
■
Dedicated clock inputs
Dual
(DPCLK and CDPCLK)
I/O input
PLL outputs
Internal logic
Dynamic GCLK clock source selection (not applicable for DPCLK, CDPCLK , and
internal logic input)
GCLK network power down (dynamic enable and disable)
- purpose clock
lists the sources that can feed the clock control block, which in turn feeds the
Input
5–11,
Figure 5–3 on page
Dedicated clock input pins can drive clocks or global signals, such as
synchronous and asynchronous clears, presets, or clock enables onto
given GCLKs.
DPCLK and CDPCLK I/O pins are bidirectional dual function pins that
are used for high fan
TRDY and IRDY signals for PCI, via the GCLK. Clock control blocks
that have inputs driven by dual
drive PLL inputs.
PLL counter outputs can drive the GCLK.
You can drive the GCLK through logic array routing to enable internal
logic elements (LEs) to drive a high fan
Clock control blocks that have inputs driven by internal logic are not
able to drive PLL inputs.
Guidelines.
- out control signals, such as protocol signals,
5–12, and
Description
- purpose clock I/O pins are not able to
Figure 5–4 on page
Cyclone IV Device Handbook, Volume 1
- out, low - skew signal path.
5–13.
5–9