FDC37C665GT-MS SMSC, FDC37C665GT-MS Datasheet - Page 104

• Manufacturer Part Number: FDC37C665GT-MS
• Description: IC CTRLR SUPER I/O MULTI 100-QFP
• Manufacturer: SMSC

Specifications of FDC37C665GT-MS

• Controller Type: I/O Controller
• Interface: ISA Host
• Voltage - Supply: 4.5 V ~ 5.5 V
• Current - Supply: 35mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 100-QFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 638-1007

DATA and ecpAFifo PORT
ADDRESS OFFSET = 00H
Modes 000 and 001 (Data Port)
The Data Port is located at an offset of '00H'
from the base address.
cleared at initialization by RESET.
WRITE operation, the Data Register latches the
contents of the data bus on the rising edge of
the nIOW input. The contents of this register
are buffered (non inverting) and output onto the
PD0 - PD7 ports. During a READ operation,
PD0 - PD7 ports are read and output to the host
CPU.
Mode 011 (ECP FIFO - Address/RLE)
A data byte written to this address is placed in
the FIFO and tagged as an ECP Address/RLE.
The hardware at the ECP port transmitts this
byte to the peripheral automatically.
operation of this register is ony defined for the
forward direction (direction is 0). Refer to the
ECP Parallel Port Forward Timing Diagram,
located in the Timing Diagrams section of this
data sheet .
DEVICE STATUS REGISTER (dsr)
ADDRESS OFFSET = 01H
The Status Port is located at an offset of '01H'
from the base address.
implemented as register bits, during a read of
the Printer Status Register these bits are a low
level. The bits of the Status Port are defined as
follows:
BIT 3 nFault
The level on the nFault input is read by the CPU
as bit 3 of the Device Status Register.
BIT 4 Select
The level on the Select input is read by the CPU
as bit 4 of the Device Status Register.
The data register is
Bits 0 - 2 are not
During a
The
104
BIT 5 PError
The level on the PError input is read by the CPU
as bit 5 of the Device Status Register. Printer
Status Register.
BIT 6 nAck
The level on the nAck input is read by the CPU
as bit 6 of the Device Status Register.
BIT 7 nBusy
The complement of the level on the BUSY input
is read by the CPU as bit 7 of the Device Status
Register.
DEVICE CONTROL REGISTER (dcr)
ADDRESS OFFSET = 02H
The Control Register is located at an offset of
'02H' from the base address.
Register is initialized to zero by the RESET
input, bits 0 to 5 only being affected; bits 6 and
7 are hard wired low.
BIT 0 STROBE - STROBE
This bit is inverted and output onto the
nSTROBE output.
BIT 1 AUTOFD - AUTOFEED
This bit is inverted and output onto the
nAUTOFD output. A logic 1 causes the printer
to generate a line feed after each line is printed.
BIT 2 nINIT - nINITIATE OUTPUT
This bit is output onto the nINIT output without
inversion.
BIT 3 SELECTIN
This bit is inverted and output onto the nSLCTIN
output. A logic 1 on this bit selects the printer; a
logic 0 means the printer is not selected.
BIT 4
ENABLE
The interrupt request enable bit when set to a
high level may be used to enable interrupt
requests from the Parallel Port to the CPU due
A logic 0 means no autofeed.
ackIntEn - INTERRUPT REQUEST
The Control