DSPIC30F6014A-30I/PT Microchip Technology Inc., DSPIC30F6014A-30I/PT Datasheet - Page 177

• Manufacturer Part Number: DSPIC30F6014A-30I/PT
• Description: DSP, 16-Bit, 144 KB Flash, 8KB RAM, 68 I/O, TQFP-80
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC30F6014A-30I/PT

• A/d Inputs: 16-Channels, 12-Bit
• Cpu Speed: 30 MIPS
• Eeprom Memory: 4K Bytes
• Input Output: 68
• Interface: CAN, I2C, SPI, UART/USART
• Ios: 68
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 80-pin TQFP
• Programmable Memory: 144K Bytes
• Ram Size: 8K Bytes
• Timers: 5-16-bit, 2-32-bit
• Voltage, Range: 2.5-5.5
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

23.0
This section provides an overview of dsPIC30F electrical characteristics. Additional information will be provided in future
revisions of this document as it becomes available.
For detailed information about the dsPIC30F architecture and core, refer to dsPIC30F Family Reference Manual
(DS70046).
Absolute maximum ratings for the dsPIC30F family are listed below. Exposure to these maximum rating conditions for
extended periods may affect device reliability. Functional operation of the device at these or any other conditions above
the parameters indicated in the operation listings of this specification is not implied.
Absolute Maximum Ratings
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any pin with respect to V
Voltage on V
Voltage on MCLR with respect to V
Maximum current out of V
Maximum current into V
Input clamp current, I
Output clamp current, I
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports
Note 1:
23.1
TABLE 23-1:
© 2006 Microchip Technology Inc.
†
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
2:
V
ELECTRICAL CHARACTERISTICS
DC Characteristics
DD
4.5-5.5V
4.5-5.5V
3.0-3.6V
3.0-3.6V
2.5-3.0V
Voltage spikes below V
Thus, a series resistor of 50-100
than pulling this pin directly to V
Maximum allowable current is a function of device maximum power dissipaton. See Table 23-2 for P
DD
Range
with respect to V
OPERATING MIPS VS. VOLTAGE
IK
dsPIC30F6011A/6012A/6013A/6014A
OK
(V
DD
I
SS
(V
< 0 or V
pin
O
pin ...........................................................................................................................300 mA
(2)
< 0 or V
...........................................................................................................................250 mA
SS
SS
I
SS
SS
> V
......................................................................................................... -0.3V to +5.5V
(†)
-40°C to 125°C
-40°C to 125°C
at the MCLR/V
-40°C to 85°C
-40°C to 85°C
-40°C to 85°C
Temp Range
(2)
....................................................................................................... 0V to +13.25V
O
(except V
DD
...............................................................................................................200 mA
> V
) .......................................................................................................... ±20 mA
SS
DD
.
should be used when applying a “low” level to the MCLR/V
) ...................................................................................................±20 mA
DD
Preliminary
and MCLR)
PP
pin, inducing currents greater than 80 mA, may cause latchup.
dsPIC30F601xA-30I
(1)
................................................ -0.3V to (V
30
20
10
—
—
Max MIPS
dsPIC30F601xA-20E
DS70143C-page 175
—
20
—
15
—
PP
pin, rather
DD
+ 0.3V)
DMAX
.