DSPIC30F6014A-30I/PT Microchip Technology Inc., DSPIC30F6014A-30I/PT Datasheet - Page 43

• Manufacturer Part Number: DSPIC30F6014A-30I/PT
• Description: DSP, 16-Bit, 144 KB Flash, 8KB RAM, 68 I/O, TQFP-80
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC30F6014A-30I/PT

• A/d Inputs: 16-Channels, 12-Bit
• Cpu Speed: 30 MIPS
• Eeprom Memory: 4K Bytes
• Input Output: 68
• Interface: CAN, I2C, SPI, UART/USART
• Ios: 68
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 80-pin TQFP
• Programmable Memory: 144K Bytes
• Ram Size: 8K Bytes
• Timers: 5-16-bit, 2-32-bit
• Voltage, Range: 2.5-5.5
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

4.2.1
The Modulo Addressing scheme requires that a start-
ing and an ending address be specified and loaded into
the 16-bit Modulo Buffer Address registers: XMODSRT,
XMODEND, YMODSRT, YMODEND (see Table 3-3).
The length of a circular buffer is not directly specified.
It is determined by the difference between the corre-
sponding start and end addresses. The maximum
possible length of the circular buffer is 32K words
(64 Kbytes).
FIGURE 4-1:
© 2006 Microchip Technology Inc.
Note:
Byte
Address
0x1100
0x1163
START AND END ADDRESS
Y space Modulo Addressing EA calcula-
tions assume word sized data (LSb of
every EA is always clear).
Start Addr = 0x1100
End Addr = 0x1163
Length = 0x0032 words
MODULO ADDRESSING OPERATION EXAMPLE
dsPIC30F6011A/6012A/6013A/6014A
MOV
MOV
MOV
MOV
MOV
MOV
MOV
MOV
DO
MOV
Preliminary
#0x1100,W0
W0,XMODSRT
#0x1163,W0
W0,MODEND
#0x8001,W0
W0,MODCON
#0x0000,W0
#0x1110,W1
AGAIN,#0x31
W0,[W1++]
4.2.2
The Modulo and Bit-Reversed Addressing Control reg-
ister MODCON<15:0> contains enable flags as well as
a W register field to specify the W address registers.
The XWM and YWM fields select which registers will
operate with Modulo Addressing. If XWM = 15, X
RAGU and X WAGU Modulo Addressing is disabled.
Similarly, if YWM = 15, Y AGU Modulo Addressing is
disabled.
The X Address Space Pointer W register (XWM), to
which Modulo Addressing is to be applied, is stored in
MODCON<3:0> (see Table 3-3). Modulo Addressing is
enabled for X data space when XWM is set to any value
other than ‘15’ and the XMODEN bit is set at
MODCON<15>.
The Y Address Space Pointer W register (YWM), to
which Modulo Addressing is to be applied, is stored in
MODCON<7:4>. Modulo Addressing is enabled for Y
data space when YWM is set to any value other than
‘15’ and the YMODEN bit is set at MODCON<14>.
;set modulo start address
;set modulo end address
;enable W1, X AGU for modulo
;W0 holds buffer fill value
;point W1 to buffer
;fill the 50 buffer locations
;fill the next location
W ADDRESS REGISTER
SELECTION
DS70143C-page 41