PIC24FJ256DA210-I/PT Microchip Technology Inc., PIC24FJ256DA210-I/PT Datasheet - Page 256

• Manufacturer Part Number: PIC24FJ256DA210-I/PT
• Description: 100 TQFP 12x12x1mm TRAY, 16-bit, 256KB Flash, 96K RAM, USB, Graphics
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ256DA210-I/PT

• A/d Inputs: 24 Channel, 10-Bit
• Comparators: 3
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 84
• Interface: I2C/SPI/UART
• Memory Capacity: 256 Kbytes
• Memory Type: Flash
• Number Of Bits: 16
• Number Of Leads: 100
• Number Of Pins: 100
• Package Type: 100-Pin TQFP
• Programmable Memory: 256K Bytes
• Ram Size: 96K Bytes
• Speed: 32 MHz
• Temperature Range: –40 to +85 °C
• Timers: 5-16-bit
• Voltage, Range: 2.2-3.6 V
• Voltage, Rating: 2.2-3.6 V
• Run Mode: 800 μA/MIPS, 3.3 V Typical
• Standby Current With 32 Khz Oscillator: 22 μA, 3.3 V Typical
• Lead Free Status / Rohs Status: RoHS Compliant part

PIC24FJ256DA210 FAMILY
REGISTER 18-4:
DS39969B-page 256
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
DPPULUP
R/W-0
U-0
—
These bits are only used in Host mode; do not use in Device mode.
Unimplemented: Read as ‘0’
DPPULUP: D+ Pull-up Enable bit
1 = D+ data line pull-up resistor is enabled
0 = D+ data line pull-up resistor is disabled
DMPULUP: D- Pull-up Enable bit
1 = D- data line pull-up resistor is enabled
0 = D- data line pull-up resistor is disabled
DPPULDWN: D+ Pull-Down Enable bit
1 = D+ data line pull-down resistor is enabled
0 = D+ data line pull-down resistor is disabled
DMPULDWN: D- Pull-Down Enable bit
1 = D- data line pull-down resistor is enabled
0 = D- data line pull-down resistor is disabled
VBUSON: V
1 = V
0 = V
OTGEN: OTG Features Enable bit
1 = USB OTG is enabled; all D+/D- pull-up and pull-down bits are enabled
0 = USB OTG is disabled; D+/D- pull-up and pull-down bits are controlled in hardware by the settings
VBUSCHG: V
1 = V
0 = V
VBUSDIS: V
1 = V
0 = V
DMPULUP
R/W-0
U-0
of the HOSTEN and USBEN (U1CON<3,0>) bits
—
BUS
BUS
BUS
BUS
BUS
BUS
U1OTGCON: USB ON-THE-GO CONTROL REGISTER
line is powered
line is not powered
line is set to charge to 3.3V
line is discharged through a resistor
line is not discharged
line is set to charge to 5V
BUS
BUS
W = Writable bit
‘1’ = Bit is set
DPPULDWN
BUS
Power-on bit
Discharge Enable bit
R/W-0
Charge Select bit
U-0
—
(1)
(1)
DMPULDWN
(1)
R/W-0
(1)
U-0
—
(1)
(1)
(1)
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
VBUSON
R/W-0
U-0
—
(1)
OTGEN
R/W-0
U-0
—
(1)
 2010 Microchip Technology Inc.
x = Bit is unknown
VBUSCHG
R/W-0
U-0
—
(1)
VBUSDIS
R/W-0
U-0
—
bit 8
bit 0
(1)