DS32512N# Maxim Integrated Products, DS32512N# Datasheet - Page 21

• Manufacturer Part Number: DS32512N#
• Description: IC LIU DS3/E3/STS-1 484-BGA
• Manufacturer: Maxim Integrated Products
• Type: Line Interface Units (LIUs)r

Specifications of DS32512N#

• Protocol: DS3
• Voltage - Supply: 3.135 V ~ 3.465 V
• Mounting Type: Surface Mount
• Package / Case: 484-BGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -

Table 7-6. Parallel Interface Pin Descriptions
RDY/ACK
WR/R/W
GPIOAn
GPIOBn
BSWAP
D[15:0]
A[10:1]
NAME
RD/DS
A[0] /
ALE
INT
CS
TYPE
I/Opd
I/Opd
I/O
Oz
Oz
I
I
I
I
I
I
Chip Select (Active Low). This pin must be asserted to read or write internal registers. See
Section 8.8.3.
Read Enable (Active Low)/Data Strobe (Active Low)
RD
DS
the
Write Enable (Active Low)/Read/Write Select
WR
R/W: For the Motorola-style bus
with
Address Latch Enable. This pin controls a latch on the A[10:0] inputs. For a nonmultiplexed
parallel bus, ALE is wired high to make the latch transparent. For a multiplexed parallel bus, the
falling edge of ALE latches the address. See Section 8.8.3.
Address Bus (Excluding LSB). These inputs specify the address of the internal 16-bit register
to be accessed. A10 is not present on the DS32506. See Section 8.8.
A[0]: This pin is connected to the lower address bit in 8-bit bus modes
0 = Output register bits 7:0 on D[7:0]; D[15:8] high impedance
1 = Output register bits 15:8 on D[7:0]; D[15:8] high impedance
BSWAP: This pin is tied high or low in 16-bit bus modes
0 = Output register bits 15:8 on D[15:8] and bits 7:0 on D[7:0]
1 = Output register bits 7:0 on D[15:8] and bits 15:8 on D[7:0]
Data Bus. A 8-bit or 16-bit bidirectional data bus. These pins are inputs during writes to internal
registers and outputs during reads. D[15:8] are disabled (high impedance) in 8-bit bus modes
(IFSEL
modes
high. See Section 8.8.
Ready Handshake (Tri-State)/Acknowledge Handshake (Tri-State, Active Low). Tri-stated
when
RDY: Intel Mode (IFSEL = 100 or 110): RDY goes high when the read or write cycle can
progress.
ACK
progress.
Interrupt Output (Active Low, Open Drain, or Push-Pull). This pin is driven low in response
to one or more unmasked, active interrupt sources within the device. INT remains low until the
interrupt is serviced or masked. When GLOBAL.CR2:INTM = 0,
inactive (default). When INTM = 1,
when
General-Purpose I/O A. When a microprocessor interface is enabled
the “A” general-purpose I/O pin for port n. See Section 8.7.3.
General-Purpose I/O B. When a microprocessor interface is enabled
the “B” general-purpose I/O pin for port n. See Section 8.7.3. Note: GPIOB1, GPIOB2, and
GPIOB3 can also be programmed as global control/status pins.
Address Bus LSB/Byte Swap. See Section 8.8.2.
: For the Motorola-style bus
: For the Intel-style bus
: For the Intel-style bus
R/W
R/W
: Motorola Mode (IFSEL = 101 or 111): ACK goes low when the read or write cycle can
CS
RST
(IFSEL
= 10X). D[15:0] are disabled (high impedance) when
pin specifies whether the access is a read or a write. See Section 8.8.3.
= 1 indicating a read and
= 1 or
= 0. See Section 8.10.
= 11X) the upper and lower bytes can be swapped by pulling the
RST
= 0. See Section 8.8.
(IFSEL
(IFSEL
21 of 130
(IFSEL
(IFSEL
= 1X0),
= 1X0),
INT
R/W
= 1X1),
is driven high when inactive.
= 1X1),
= 0 indicating a write. See Section 8.8.3.
FUNCTION
RD
WR
is asserted to read internal registers.
DS
is asserted to write internal registers.
R/W
is asserted to access internal registers while
determines the type of bus transaction,
(IFSEL
CS
= 11X).
INT
DS32506/DS32508/DS32512
= 1 or
is high impedance when
INT
(IFSEL
(IFSEL
(IFSEL
RST
is high impedance
= 0. In 16-bit bus
≠ 000), this pin is
≠ 000), this pin is
= 10X).
BSWAP
pin