ISP1563BMUM ST-Ericsson Inc, ISP1563BMUM Datasheet - Page 8

• Manufacturer Part Number: ISP1563BMUM
• Description: IC USB HOST CTRL HI-SPD 128LQFP
• Manufacturer: ST-Ericsson Inc

Specifications of ISP1563BMUM

• Applications: USB Host/Function Processor
• Interface: EHCI Interface
• Voltage - Supply: 3 V ~ 3.6 V
• Package / Case: 128-LQFP
• Mounting Type: Surface Mount
• For Use With: UM10066 - EVAL BRD FOR ISP1563
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ISP1563BM-T; ISP1563BM-T

Philips Semiconductors
9397 750 14224
Product data sheet
Table 2:
Symbol
CLKRUN#
REG1V8
PERR#
SERR#
GNDA
PAR
C/BE#[1]
GNDD
AD[15]
AD[14]
AD[13]
AMB4
GRN4
AD[12]
AD[11]
V
AD[10]
AD[9]
CC(I/O)
[1]
Pin description
Pin
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
Type
I/O
-
I/O
I/O
-
I/O
I/O
-
I/O
I/O
I/O
I/O
O
I/O
I/O
-
I/O
I/O
Rev. 01 — 14 July 2005
…continued
Description
PCI CLKRUN signal; pull-down to ground through a 10 kΩ resistor
PCI pad; 3.3 V signaling; open-drain
1.8 V regulator output voltage; only for voltage conditioning; cannot
be used to supply power to external components; add a 100 nF
decoupling capacitor
PCI parity error; used to report data parity errors during all PCI
transactions, except a Special Cycle
PCI pad; 3.3 V signaling
PCI system error; used to report address parity errors and data parity
errors on the Special Cycle command, or any other system error in
which the result will be catastrophic
PCI pad; 3.3 V signaling; open-drain
analog ground
PCI parity
PCI pad; 3.3 V signaling
byte 1 of multiplexed PCI bus command and byte enable
PCI pad; 3.3 V signaling
digital ground
bit 15 of multiplexed PCI address and data
PCI pad; 3.3 V signaling
bit 14 of multiplexed PCI address and data
PCI pad; 3.3 V signaling
bit 13 of multiplexed PCI address and data
PCI pad; 3.3 V signaling
amber LED indicator output for the USB downstream port 4; this pin
acts as an input only during the power-up sequence and thereafter,
acts as an output:
3.3 V bidirectional pad; three-state output; 3 ns slew-rate control;
input; CMOS; open-drain
green LED indicator output for the USB downstream port 4; the LED
is off by default; the LED can be programmed to enable it to blink
3.3 V output pad; 3 ns slew rate control; CMOS; open-drain
bit 12 of multiplexed PCI address and data
PCI pad; 3.3 V signaling
bit 11 of multiplexed PCI address and data
PCI pad; 3.3 V signaling
3.3 V supply voltage; used to power pads; add a 100 nF decoupling
capacitor
bit 10 of multiplexed PCI address and data
PCI pad; 3.3 V signaling
bit 9 of multiplexed PCI address and data
PCI pad; 3.3 V signaling
•
•
HIGH: FFh in the PMC register; supports D3
LOW: EFh in the PMC register; does not support D3
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
HS USB PCI Host Controller
cold
ISP1563
cold
.
8 of 107