ATMEGA328P-20PU Atmel, ATMEGA328P-20PU Datasheet - Page 21

• Manufacturer Part Number: ATMEGA328P-20PU
• Manufacturer: Atmel

Specifications of ATMEGA328P-20PU

• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: SPI/TWI/USART
• Program Memory Type: Flash
• Program Memory Size: 32KB
• Total Internal Ram Size: 2KB
• # I/os (max): 23
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 6-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 28
• Package Type: PDIP
• Lead Free Status / Rohs Status: Compliant

7.6
7.6.1
7.6.2
7.6.3
8025K–AVR–10/09
Register Description
EEARH and EEARL – The EEPROM Address Register
EEDR – The EEPROM Data Register
EECR – The EEPROM Control Register
• Bits 15..9 – Res: Reserved Bits
These bits are reserved bits in the ATmega48P/88P/168P and will always read as zero.
• Bits 8..0 – EEAR8..0: EEPROM Address
The EEPROM Address Registers – EEARH and EEARL specify the EEPROM address in the
256/512/512 bytes EEPROM space. The EEPROM data bytes are addressed linearly between 0
and 255/511/511. The initial value of EEAR is undefined. A proper value must be written before
the EEPROM may be accessed.
EEAR8 is an unused bit in ATmega48P and must always be written to zero.
• Bits 7..0 – EEDR7.0: EEPROM Data
For the EEPROM write operation, the EEDR Register contains the data to be written to the
EEPROM in the address given by the EEAR Register. For the EEPROM read operation, the
EEDR contains the data read out from the EEPROM at the address given by EEAR.
• Bits 7..6 – Res: Reserved Bits
These bits are reserved bits in the ATmega48P/88P/168P and will always read as zero.
• Bits 5, 4 – EEPM1 and EEPM0: EEPROM Programming Mode Bits
The EEPROM Programming mode bit setting defines which programming action that will be trig-
gered when writing EEPE. It is possible to program data in one atomic operation (erase the old
value and program the new value) or to split the Erase and Write operations in two different
operations. The Programming times for the different modes are shown in
Bit
0x22 (0x42)
0x21 (0x41)
Read/Write
Initial Value
Bit
0x20 (0x40)
Read/Write
Initial Value
Bit
0x1F (0x3F)
Read/Write
Initial Value
EEAR7
MSB
R/W
R/W
15
R
R
–
7
0
X
7
0
7
–
0
EEAR6
R/W
R/W
14
R
R
–
6
0
X
6
0
6
–
0
EEPM1
EEAR5
R/W
R/W
R/W
13
R
5
X
–
5
0
X
5
0
EEPM0
EEAR4
R/W
R/W
R/W
12
X
R
4
–
4
0
X
4
0
EEAR3
EERIE
R/W
R/W
R/W
11
R
3
0
–
3
0
X
3
0
ATmega48P/88P/168P
EEMPE
EEAR2
R/W
R/W
R/W
10
R
–
2
0
X
2
0
2
0
EEAR1
EEPE
R/W
R/W
R/W
R
9
–
1
0
X
1
0
X
1
Table
EEAR8
EEAR0
EERE
7-1. While EEPE
R/W
R/W
LSB
R/W
R/W
X
X
8
0
0
0
0
0
EEARH
EEARL
EEDR
EECR
21