P80C592FFA NXP Semiconductors, P80C592FFA Datasheet - Page 26
![](/photos/31/32/313213/sot188-2_sml.jpg)
P80C592FFA
Manufacturer Part Number
P80C592FFA
Description
Manufacturer
NXP Semiconductors
Datasheet
1.P80C592FFA.pdf
(108 pages)
Specifications of P80C592FFA
Cpu Family
80C
Device Core
80C51
Device Core Size
8b
Frequency (max)
16MHz
Interface Type
CAN/UART
Program Memory Type
ROMLess
Program Memory Size
Not Required
Total Internal Ram Size
512Byte
# I/os (max)
40
Number Of Timers - General Purpose
3
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
4.5V
On-chip Adc
8-chx10-bit
Instruction Set Architecture
CISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
68
Package Type
PLCC
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P80C592FFA
Manufacturer:
PANASONIC
Quantity:
1 200
Part Number:
P80C592FFA
Manufacturer:
PHI
Quantity:
20 000
Company:
Part Number:
P80C592FFA/00
Manufacturer:
SYSTECH
Quantity:
40
Part Number:
P80C592FFA/00
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
P80C592FFA/00,512
Manufacturer:
ON
Quantity:
300
Company:
Part Number:
P80C592FFA/00,512
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P80C592FFA/00,518
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P80C592FFA/00Ј¬512
Manufacturer:
NXP
Quantity:
702
Philips Semiconductors
11.3
In addition to Timer T2 and the standard timers (Timer 0
and Timer 1), a Watchdog Timer (WDT) comprising an
11-bit prescaler and an 8-bit timer (T3) is also provided
(see Fig.12).
The timer T3 is incremented every 1.5 ms, derived from
the oscillator frequency of 16 MHz by the following
formula:
When a timer T3 overflow occurs, the microcontroller is
reset and a reset-output-pulse is generated at pin RST.
This short output pulse (3 machine cycles) may be
suppressed if the RST pin is connected to a capacitor.
To prevent a system reset (by an overflow of the WDT), the
user program has to reload T3 within periods that are
shorter than the programmed Watchdog time interval.
If the processor suffers a hardware/software malfunction,
the software will fail to reload the timer. This failure will
produce a reset upon overflow thus preventing the
processor running out of control.
1996 Jun 27
8-bit microcontroller with on-chip CAN
Watchdog Timer (T3)
1/12 f CLK
f
timer
EW
=
------------------------- -
12 2048
f
CLK
write
T3
PRESCALER
Fig.12 Functional diagram of T3 Watchdog Timer.
11-BIT
CLEAR
TIMER T3 (8-BIT)
PCON.4
INTERNAL BUS
INTERNAL BUS
LOAD
26
CLEAR
The Watchdog Timer can only be reloaded if the condition
flag WLE = PCON.4 has been previously set by software.
At the moment the counter is loaded the condition flag is
automatically cleared.
The timer interval between the timer's reloading and the
occurrence of a reset depends on the reloaded value. For
example, this may range from 1.5 ms to 0.375 s when
using an oscillator frequency of 16 MHz.
In the Idle state the Watchdog Timer and reset circuitry
remain active.
The Watchdog Timer (WDT) is controlled by the Enable
Watchdog pin (EW) (see Table 28).
Table 28 EW controlling WDT and Power-down mode
WLE
PIN EW
LOADEN
HIGH
LOW
internal
reset
overflow
disabled
enabled
LOADEN
WDT
PD
PCON.1
POWER-DOWN MODE
Product specification
V DD
P
disabled
enabled
R RST
P8xC592
MGA157
RST