P80C592FFA/00,518 NXP Semiconductors, P80C592FFA/00,518 Datasheet - Page 69
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
P80C592FFA/00,518
Manufacturer Part Number
P80C592FFA/00,518
Description
IC 80C51 MCU 8BIT ROMLESS 68PLCC
Manufacturer
NXP Semiconductors
Series
80Cr
Datasheet
1.P80C592FFA00512.pdf
(108 pages)
Specifications of P80C592FFA/00,518
Core Processor
8051
Core Size
8-Bit
Speed
16MHz
Connectivity
CAN, EBI/EMI, UART/USART
Peripherals
DMA, POR, PWM, WDT
Number Of I /o
48
Program Memory Size
-
Program Memory Type
ROMless
Eeprom Size
-
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
68-LCC (J-Lead)
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P80C592FFA/00,518
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
15.4
The instruction that sets bit PCON.1 to HIGH, is the last
one executed before entering the Power-down mode. In
Power-down mode the oscillator of the P8xC592 is
stopped. If the CAN-controller is in use, it is recommended
to set it into Sleep mode before entering Power-down
mode. However, setting PCON.1 to HIGH also sets the
Sleep bit (CAN-controller Command Register bit 4) to
HIGH.
The P8xC592 leaves Power-down mode either by a
hardware reset or by a CAN Wake-Up interrupt
(due to activity on the CAN-bus),
if the SIO1 (CAN) interrupt source is enabled
(contents of register IEN0 = 1X1XXXXXB).
Table 82 Status of external pins during Idle and Power-down modes
Note
1. If the port pins P1.6 and P1.7 are used as the CAN transmitter outputs (CTX0 and CTX1), then during Sleep and
1996 Jun 27
Idle
Power-down
8-bit microcontroller with on-chip CAN
Power-down mode these pins output a ‘recessive’ level (see Sections 13.5.2 and 13.5.11).
MODE
Power-down Mode
internal
external
internal
external
PROGRAM
ALE
1
1
0
0
PSEN
1
1
0
0
port data
floating
port data
floating
PORT0
69
A hardware reset affects the whole P8xC592, but leaves
the contents of the on-chip RAM unchanged
(CAN-controller-and CPU's SFRs are reset, see
Section 13.5.2, Chapter 17 and Table 40). A CAN
Wake-Up interrupt during Power-down mode causes a
reset output pulse with a width of 6144 machine cycles
(4.6 ms with f
the CAN-controller of the P8xC592 is reset (i.e. the
contents of all CAN-controller registers are preserved).
A capacitance connected to the RST pin can be used to
lengthen the internally generated reset pulse. If the pulse
exceeds 8192 machine cycles, the CAN-controller part is
reset too.
port data
port data
port data
port data
PORT1
(1)
port data
address
port data
port data
CLK
PORT2
= 16 MHz). All hardware except that for
port data
port data
port data
port data
PORT3
port data
port data
port data
port data
PORT4
Product specification
P8xC592
PWM0/
PWM1
1
1
1
1