AT32UC3B1128 Atmel Corporation, AT32UC3B1128 Datasheet - Page 140

• Manufacturer Part Number: AT32UC3B1128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B1128

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 28
• Ext Interrupts: 28
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

15.4.2.2
32059L–AVR32–01/2012
Round-Robin Arbitration
In order to avoid long slave handling during undefined length bursts (INCR), the Bus Matrix pro-
vides specific logic in order to re-arbitrate before the end of the INCR transfer. A predicted end
of burst is used as a defined length burst transfer and can be selected from among the following
five possibilities:
This selection can be done through the field ULBT of the Master Configuration Registers
(MCFG).
The Bus Matrix contains specific logic to break long accesses, such as very long bursts on a
very slow slave (e.g., an external low speed memory). At the beginning of the burst access, a
counter is loaded with the value previously written in the SLOT_CYCLE field of the related Slave
Configuration Register (SCFG) and decreased at each clock cycle. When the counter reaches
zero, the arbiter has the ability to re-arbitrate at the end of the current byte, half word or word
transfer.
This algorithm allows the Bus Matrix arbiters to dispatch the requests from different masters to
the same slave in a round-robin manner. If two or more master requests arise at the same time,
the master with the lowest number is first serviced, then the others are serviced in a round-robin
manner.
There are three round-robin algorithms implemented:
This is the main algorithm used by Bus Matrix arbiters. It allows the Bus Matrix to dispatch
requests from different masters to the same slave in a pure round-robin manner. At the end of
3. End of Burst Cycles: When the current cycle is the last cycle of a burst transfer. For
4. Slot Cycle Limit: When the slot cycle counter has reached the limit value indicating that
• Undefined Length Burst Arbitration
1. Infinite: No predicted end of burst is generated and therefore INCR burst transfer will
2. One beat bursts: Predicted end of burst is generated at each single transfer inside the
3. Four beat bursts: Predicted end of burst is generated at the end of each four beat
4. Eight beat bursts: Predicted end of burst is generated at the end of each eight beat
5. Sixteen beat bursts: Predicted end of burst is generated at the end of each sixteen beat
• Slot Cycle Limit Arbitration
1. Round-Robin arbitration without default master
2. Round-Robin arbitration with last default master
3. Round-Robin arbitration with fixed default master
• Round-Robin Arbitration without Default Master
defined length burst, predicted end of burst matches the size of the transfer but is man-
aged differently for undefined length burst.
the current master access is too long and must be broken.
never be broken.
INCP transfer.
boundary inside INCR transfer.
boundary inside INCR transfer.
boundary inside INCR transfer.
140