AT32UC3L0256 Atmel Corporation, AT32UC3L0256 Datasheet - Page 603
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT32UC3L0256
Manufacturer Part Number
AT32UC3L0256
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(159 pages)
3.AT32UC3L0128.pdf
(85 pages)
4.AT32UC3L0128.pdf
(852 pages)
Specifications of AT32UC3L0256
Flash (kbytes)
256 Kbytes
Pin Count
48
Max. Operating Frequency
50 MHz
Cpu
32-bit AVR
# Of Touch Channels
17
Hardware Qtouch Acquisition
Yes
Max I/o Pins
36
Ext Interrupts
36
Usb Speed
No
Usb Interface
No
Spi
5
Twi (i2c)
2
Uart
4
Lin
4
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
12
Adc Speed (ksps)
460
Analog Comparators
8
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
16
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.62 to 3.6
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
18
Input Capture Channels
12
Pwm Channels
35
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT32UC3L0256-D3HR
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
AT32UC3L0256-H
Manufacturer:
ATMEL
Quantity:
270
Part Number:
AT32UC3L0256-H
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
- AT32UC3A0128 PDF datasheet
- AT32UC3A0128 PDF datasheet #2
- AT32UC3L0128 PDF datasheet #3
- AT32UC3L0128 PDF datasheet #4
- Current page: 603 of 852
- Download datasheet (13Mb)
25.5
32145A–12/2011
Application Example
tem will only be woken up if the user peripheral generates an interrupt as a result of the
operation. This concept is known as SleepWalking and is described in further detail in the Power
Manager chapter. Note that asynchronous peripheral events may be associated with a delay
due to the need to restart the system clock source if this has been stopped in the sleep mode.
This application example shows how the Peripheral Event System can be used to program the
ADC Interface to perform ADC conversions at selected intervals.
Conversions of the active analog channels are started with a software or a hardware trigger.
One of the possible hardware triggers is a peripheral event trigger, allowing the Peripheral Event
System to synchronize conversion with some configured peripheral event source. From
25-3
peripheral event, or an event from the PWM Controller. The AST can generate periodic periph-
eral events at selected intervals, among other types of peripheral events. The Peripheral Event
System can then be used to set up the ADC Interface to sample an analog signal at regular
intervals.
The user must enable peripheral events in the AST and in the ADC Interface to accomplish this.
The periodic peripheral event in the AST is enabled by writing a one to the corresponding bit in
the AST Event Enable Register (EVE). To select the peripheral event trigger for the ADC Inter-
face, the user must write the value 0x7 to the Trigger Mode (TRGMOD) field in the ADC
Interface Trigger Register (TRGR). When the peripheral events are enabled, the AST will gener-
ate peripheral events at the selected intervals, and the Peripheral Event System will route the
peripheral events to the ADC Interface, which will perform ADC conversions at the selected
intervals.
Figure 25-2. Application Example
Since the AST peripheral event is asynchronous, the description above will also work in sleep
modes where the ADC clock is stopped. In this case, the ADC clock (and clock source, if
needed) will be restarted during the ADC conversion. After the conversion, the ADC clock and
clock source will return to the sleep state, unless the ADC generates an interrupt, which in turn
will wake up the system. Using asynchronous interrupts thus allows ADC operation in much
lower power states than would otherwise be possible.
and
Table
AST
Periodic peripheral
25-4, it can be read that this peripheral event source can be either an AST
event
Peripheral
System
Event
conversion
Trigger
AT32UC3L0128/256
Interface
ADC
Table
603
Related parts for AT32UC3L0256
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
![ATF22V10B-25PC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
![AT89C51ED2-IM](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
![AT24C01](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
![U6046B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: