AT89LP3240 Atmel Corporation, AT89LP3240 Datasheet - Page 82
AT89LP3240
Manufacturer Part Number
AT89LP3240
Description
Manufacturer
Atmel Corporation
Datasheet
1.AT89LP3240.pdf
(200 pages)
Specifications of AT89LP3240
Flash (kbytes)
32 Kbytes
Max. Operating Frequency
20 MHz
Cpu
8051-1C
Max I/o Pins
38
Spi
1
Twi (i2c)
1
Uart
1
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
153.8
Sram (kbytes)
4.25
Eeprom (bytes)
8192
Self Program Memory
IAP
Operating Voltage (vcc)
2.4 to 3.6
Timers
3
Isp
SPI/OCD
Watchdog
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 82 of 200
- Download datasheet (7Mb)
Figure 13-14. Multi-Phasic PWM Modes
14. External Interrupts
82
AT89LP3240/6440
PHSD
PHSD
CCA
CCB
CCC
CCD
CCA
CCB
CCC
CCD
CCA
CCB
CCC
CCD
CCA
CCB
CCC
CCD
CCA
CCB
CCC
CCD
The INT0 (P3.2) and INT1 (P3.3) pins of the AT89LP3240/6440 may be used as external inter-
rupt sources. The external interrupts can be programmed to be level-activated or transition-
activated by setting or clearing bit IT1 or IT0 in Register TCON. If ITx = 0, external interrupt x is
triggered by a detected low at the INTx pin. If ITx = 1, external interrupt x is edge-triggered. In
this mode if successive samples of the INTx pin show a high in one cycle and a low in the next
cycle, interrupt request flag IEx in TCON is set. Flag bit IEx then requests the interrupt. Since the
external interrupt pins are sampled once each clock cycle, an input high or low should hold for at
least 2 oscillator periods to ensure sampling. If the external interrupt is transition-activated, the
external source has to hold the request pin high for at least two clock cycles, and then hold it low
for at least two clock cycles to ensure that the transition is seen so that interrupt request flag IEx
will be set. IEx will be automatically cleared by the CPU when the service routine is called if gen-
erated in edge-triggered mode. If the external interrupt is level-activated, the external source has
to hold the request active until the requested interrupt is actually generated. Then the external
source must deactivate the request before the interrupt service routine is completed, or else
PHS = 000B
PHS = 001B
PHS = 010B
PHS = 011B
PHS = 100B
3706C–MICRO–2/11
Related parts for AT89LP3240
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-Bit Microcontroller with 4K Bytes Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: