AT90PWM1 Atmel Corporation, AT90PWM1 Datasheet - Page 229

• Manufacturer Part Number: AT90PWM1
• Manufacturer: Atmel Corporation

Specifications of AT90PWM1

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

22.8.6
22.8.7
4378C–AVR–09/08
Reading the Flash
Reading the EEPROM
5. E: Latch data (give PAGEL a positive pulse).
K: Repeat 3 through 5 until the entire buffer is filled.
L: Program EEPROM page
1. Set BS1 to “0”.
2. Give WR a negative pulse. This starts programming of the EEPROM page. RDY/BSY
3. Wait until to RDY/BSY goes high before programming the next page (See
Figure 22-4. Programming the EEPROM Waveforms
The algorithm for reading the Flash memory is as follows (refer to
page 226
1. A: Load Command “0000 0010”.
2. G: Load Address High Byte (0x00 - 0xFF).
3. B: Load Address Low Byte (0x00 - 0xFF).
4. Set OE to “0”, and BS1 to “0”. The Flash word low byte can now be read at DATA.
5. Set BS1 to “1”. The Flash word high byte can now be read at DATA.
6. Set OE to “1”.
The algorithm for reading the EEPROM memory is as follows (refer to
on page 226
1. A: Load Command “0000 0011”.
2. G: Load Address High Byte (0x00 - 0xFF).
3. B: Load Address Low Byte (0x00 - 0xFF).
4. Set OE to “0”, and BS1 to “0”. The EEPROM Data byte can now be read at DATA.
5. Set OE to “1”.
goes low.
signal waveforms).
RESET +12V
RDY/BSY
PAGEL
XTAL1
DATA
XA1
XA0
BS1
BS2
WR
OE
for details on Command and Address loading):
for details on Command and Address loading):
0x11
A
ADDR. HIGH
G
ADDR. LOW
B
DATA
C
XX
E
ADDR. LOW
B
DATA
C
K
XX
E
“Programming the Flash” on
“Programming the Flash”
L
AT90PWM1
Figure 22-4
for
229