AT90PWM1 Atmel Corporation, AT90PWM1 Datasheet - Page 65

• Manufacturer Part Number: AT90PWM1
• Manufacturer: Atmel Corporation

Specifications of AT90PWM1

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

11.3.1
11.3.2
4378C–AVR–09/08
MCU Control Register – MCUCR
Alternate Functions of Port B
• Bit 4 – PUD: Pull-up Disable
When this bit is written to one, the pull-ups in the I/O ports are disabled even if the DDxn and
PORTxn Registers are configured to enable the pull-ups ({DDxn, PORTxn} = 0b01). Se
The Port B pins with alternate functions are shown in
Table 9. Port B Pins Alternate Functions
The alternate pin configuration is as follows:
• PSCOUT01/ADC4/SCK – Bit 7
PSCOUT01: Output 1 of PSC 0.
ADC4, Analog to Digital Converter, input channel 4
SCK: Master Clock output, Slave Clock input pin for SPI channel. When the SPI is enabled as a
slave, this pin is configured as an input regardless of the setting of DDB7. When the SPI is
enabled as a master, the data direction of this pin is controlled by DDB7. When the pin is forced
to be an input, the pull-up can still be controlled by the PORTB7 bit.
• ADC7/ICP1B/PSCOUT11 – Bit 6
ADC7, Analog to Digital Converter, input channel 7
ICP1B, Input Capture Pin: The PB6 pin can act as an Input Capture Pin for Timer/Counter1.
PSCOUT11: Output 1 of PSC 1.
Bit
Read/Write
Initial Value
Port Pin
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
PSCOUT01 output
ADC4 (Analog Input Channel 4)
SCK (SPI Bus Serial Clock)
ADC7 (Analog Input Channel 7)
ICP1B (Timer 1 input capture alternate input)
PSCOUT11 output (see note 4)
ADC6 (Analog Input Channel 6)
INT2
ADC5 (Analog Input Channel5 )
INT1
MOSI (SPI Master Out Slave In)
PSCOUT21 output
MISO (SPI Master In Slave Out)
PSCOUT20 output
Alternate Functions
AMP0+ (Analog Differential Amplifier 0 Input Channel )
AMP0- (Analog Differential Amplifier 0 Input Channel )
SPIPS
R/W
7
0
R
6
–
0
R
5
–
0
PUD
R/W
4
0
.
.
Table
R
3
–
0
9.
R
2
–
0
IVSEL
R/W
1
0
AT90PWM1
IVCE
R/W
0
0
MCUCR
65