AT90PWM2B Atmel Corporation, AT90PWM2B Datasheet - Page 296

• Manufacturer Part Number: AT90PWM2B
• Manufacturer: Atmel Corporation

Specifications of AT90PWM2B

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

Table 25-16. Serial Programming Instruction Set
296
Instruction
Programming Enable
Chip Erase
Read Program Memory
Load Program Memory Page
Write Program Memory Page
Read EEPROM Memory
Write EEPROM Memory
Load EEPROM Memory
Page (page access)
Write EEPROM Memory
Page (page access)
Read Lock bits
Write Lock bits
Read Signature Byte
Write Fuse bits
AT90PWM2/3/2B/3B
Figure 25-11. Serial Programming Waveforms
1010 1100
1010 1100
0010 H000
0100 H000
0100 1100
1010 0000
1100 0000
1100 0001
1100 0010
0101 1000
1010 1100
0011 0000
1010 1100
SERIAL DATA OUTPUT
SERIAL CLOCK INPUT
Byte 1
SERIAL DATA INPUT
SAMPLE
(MOSI)
(MISO)
0101 0011
100x xxxx
000a aaaa
000x xxxx
000a aaaa
000x xxaa
000x xxaa
0000 0000
00xx xxaa
0000 0000
111x xxxx
000x xxxx
1010 0000
(SCK)
Byte 2
Instruction Format
MSB
MSB
xxxx xxxx
xxxx xxxx
bbbb bbbb
xxbb bbbb
bbxx xxxx
bbbb bbbb
bbbb bbbb
0000 00bb
bbbb bb00
xxxx xxxx
xxxx xxxx
xxxx xxbb
xxxx xxxx
Byte 3
xxxx xxxx
xxxx xxxx
oooo oooo
iiii iiii
xxxx xxxx
oooo oooo
iiii iiii
iiii iiii
xxxx xxxx
xxoo oooo
11ii iiii
oooo oooo
iiii iiii
Byte4
Operation
Enable Serial Programming after
RESET goes low.
Chip Erase EEPROM and Flash.
Read H (high or low) data o from
Program memory at word address a:b.
Write H (high or low) data i to Program
Memory page at word address b. Data
low byte must be loaded before Data
high byte is applied within the same
address.
Write Program Memory Page at
address a:b.
Read data o from EEPROM memory at
address a:b.
Write data i to EEPROM memory at
address a:b.
Load data i to EEPROM memory page
buffer. After data is loaded, program
EEPROM page.
Write EEPROM page at address a:b.
Read Lock bits. “0” = programmed, “1”
= unprogrammed. See
page 278
Write Lock bits. Set bits = “0” to
program Lock bits. See
page 278
Read Signature Byte o at address b.
Set bits = “0” to program, “1” to
unprogram. See Table XXX on page
XXX for details.
for details.
for details.
Table 25-1 on
Table 25-1 on
LSB
LSB
4317J–AVR–08/10