AT90PWM2B Atmel Corporation, AT90PWM2B Datasheet - Page 96

• Manufacturer Part Number: AT90PWM2B
• Manufacturer: Atmel Corporation

Specifications of AT90PWM2B

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

96
AT90PWM2/3/2B/3B
• Bits 7:6 – COM0A1:0: Compare Match Output A Mode
These bits control the Output Compare pin (OC0A) behavior. If one or both of the COM0A1:0
bits are set, the OC0A output overrides the normal port functionality of the I/O pin it is connected
to. However, note that the Data Direction Register (DDR) bit corresponding to the OC0A pin
must be set in order to enable the output driver.
When OC0A is connected to the pin, the function of the COM0A1:0 bits depends on the
WGM02:0 bit setting.
are set to a normal or CTC mode (non-PWM).
Table 14-2.
Table 14-3
mode.
Table 14-3.
Note:
Table 14-4
rect PWM mode.
Table 14-4.
Note:
• Bits 5:4 – COM0B1:0: Compare Match Output B Mode
COM0A1
COM0A1
COM0A1
0
0
1
1
0
0
1
1
0
0
1
1
1. A special case occurs when OCR0A equals TOP and COM0A1 is set. In this case, the Com-
1. A special case occurs when OCR0A equals TOP and COM0A1 is set. In this case, the Com-
pare Match is ignored, but the set or clear is done at TOP. See
for more details.
pare Match is ignored, but the set or clear is done at TOP. See
page 117
shows the COM0A1:0 bit functionality when the WGM02:0 bits are set to phase cor-
shows the COM0A1:0 bit functionality when the WGM01:0 bits are set to fast PWM
Compare Output Mode, non-PWM Mode
Compare Output Mode, Fast PWM Mode
Compare Output Mode, Phase Correct PWM Mode
COM0A0
COM0A0
COM0A0
0
1
0
1
0
1
0
1
0
1
0
1
for more details.
Table 14-2
Description
Normal port operation, OC0A disconnected.
Toggle OC0A on Compare Match
Clear OC0A on Compare Match
Set OC0A on Compare Match
Description
Normal port operation, OC0A disconnected.
WGM02 = 0: Normal Port Operation, OC0A Disconnected.
WGM02 = 1: Toggle OC0A on Compare Match.
Clear OC0A on Compare Match, set OC0A at TOP
Set OC0A on Compare Match, clear OC0A at TOP
Description
Normal port operation, OC0A disconnected.
WGM02 = 0: Normal Port Operation, OC0A Disconnected.
WGM02 = 1: Toggle OC0A on Compare Match.
Clear OC0A on Compare Match when up-counting. Set OC0A on
Compare Match when down-counting.
Set OC0A on Compare Match when up-counting. Clear OC0A on
Compare Match when down-counting.
shows the COM0A1:0 bit functionality when the WGM02:0 bits
(1)
(1)
“Phase Correct PWM Mode” on
“Fast PWM Mode” on page 91
4317J–AVR–08/10