ATmega32U4 Atmel Corporation, ATmega32U4 Datasheet - Page 172

• Manufacturer Part Number: ATmega32U4
• Manufacturer: Atmel Corporation

Specifications of ATmega32U4

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 14
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 26
• Ext Interrupts: 13
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 3.3
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 2
• Pwm Channels: 8
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

15.12.11 OCR4D – Timer/Counter4 Output Compare Register D
15.12.12 TIMSK4 – Timer/Counter4 Interrupt Mask Register
7766F–AVR–11/10
The output compare register C is an 8-bit read/write register.
The Timer/Counter Output Compare Register C contains data to be continuously compared with
Timer/Counter4, and a compare match will clear TCNT4. This register has the same function in
Normal mode and PWM modes.
Note that, if a smaller value than three is written to the Output Compare Register C, the value is
automatically replaced by three as it is a minimum value allowed to be written to this register.
Note that, if 10-bit accuracy is used special procedures must be followed when accessing the
internal 10-bit Output Compare Registers via the 8-bit AVR data bus. These procedures are
described in section
The output compare register D is an 8-bit read/write register.
The Timer/Counter Output Compare Register D contains data to be continuously compared with
Timer/Counter4. Actions on compare matches are specified in TCCR4A. A compare match does
only occur if Timer/Counter4 counts to the OCR4D value. A software write that sets TCNT4 and
OCR4D to the same value does not generate a compare match.
A compare match will set the compare interrupt flag OCF4D after a synchronization delay follow-
ing the compare event.
Note that, if 10-bit accuracy is used special procedures must be followed when accessing the
internal 10-bit Output Compare Registers via the 8-bit AVR data bus. These procedures are
described in section
• Bit 7- OCIE4D: Timer/Counter4 Output Compare Interrupt Enable
When the OCIE4D bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter4 Compare Match D interrupt is enabled. The corresponding interrupt at vector
$010 is executed if a compare match D occurs. The Compare Flag in Timer/Counter4 is set
(one) in the Timer/Counter Interrupt Flag Register.
• Bit 6 - OCIE4A: Timer/Counter4 Output Compare Interrupt Enable
When the OCIE4A bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter4 Compare Match A interrupt is enabled. The corresponding interrupt at vector
$003 is executed if a compare match A occurs. The Compare Flag in Timer/Counter4 is set
(one) in the Timer/Counter Interrupt Flag Register.
Bit
Read/Write
Initial value
Bit
Read/Write
Initial value
OCIE4D
MSB
R/W
R/W
7
0
7
0
“Accessing 10-Bit Registers” on page
“Accessing 10-Bit Registers” on page
OCIE4A
R/W
R/W
6
0
6
0
OCIE4B
R/W
R/W
5
0
5
0
R/W
R/W
4
0
4
0
R/W
R/W
3
0
3
0
159.
159.
TOIE4
R/W
R/W
2
0
2
0
ATmega16/32U4
R/W
R/W
1
0
1
0
LSB
R/W
R/W
0
0
0
0
TIMSK4
OCR4D
172